Jump to content
SAU Community

Sydney 96 R33 Gtr Brand New N1 Block,nitto 2.7...............


Recommended Posts

Hi everyone

Im moving back to NZ by mid feb 2014 so im selling my car :/

All the mods are done by " Croydon Racing Development"

BLOCk(all brand new with receipts)

Brand new N1 block

Nitto 2.7 full stroker kit (86mm)

Acl race series bearings

CRD extended sump

Nitto rear oil drain kit

1000 hp ATI balancer

VRS gasket kit including drag head gasket

Arp main studs

Nitto high volume oil pump

Nismo thermostat

Gates timing belt kit

Blits racing radiator type ZS

N1 water pump

Tomei cam gears

Nitto clear cam cover

...........

TURBO AND EXHAUST

-5s 7000km old

Tomei dump pipes 7000km old

CRD front pipe 7000km old

100 cell cat convertor 7000km old

full 3.5 inch exhaust with magma mufler

HEAD

CRD full race head including guides,collets,valve springs reatainers ...all Tomei. heaveily portead and machined im running tomei 260s now but you could run 280s or 290s if you want shimming required cost me $8500

Arp head studs

700 cc powerenterprise injectors

unknow fuel pump

ELECTRONICS

HkS EVC

Haltech platnium pro plug in

Split fire coil pack

Hks turbo timer

Sterio+sub+amp (who wants to listen to music lol)

GEARBOX

OS giken 1-5 gear set including input shaft

OS giken QUAD plate clutch (I know hard to drive but i had OS 88 inmind)

Nismo engine mounts

Nismo gearbox mounts

BODY

All standard

Brand new front lip ($1300 :blush:)

ROH madena???? 18x35x265

Kumho KU36 %90 tread

140000 km the engine was done jan this year 5000km old

Car made 351 kw @22psi its currently 370 kw @24psi after installing EVC on 98

Plan was going E85 And PT6466 but no time

the car is capable of easy 600 kw+

Motul 6100 oil and was changed every 3000kms

PRICE $35000 ONO

This cost me $650000+

If i could not sell it by mid feb i will take it with me but its easier with out it

PS i will include HKS E-TS torque controller and A'PEXI drag intercooller to the right buyer

sorry for shit photos iphone

best to sms 0408844383 THANKS

post-99653-0-55880400-1387678783_thumb.jpg

post-99653-0-24796600-1387678803_thumb.jpg

post-99653-0-92557400-1387678838_thumb.jpg

post-99653-0-43421500-1387678860_thumb.jpg

post-99653-0-94757300-1387678877_thumb.jpg

post-99653-0-35061200-1387678895_thumb.jpg

post-99653-0-99629300-1387678912_thumb.jpg

post-99653-0-50985500-1387678930_thumb.jpg

post-99653-0-86190700-1387678950_thumb.jpg

post-99653-0-99804000-1387678966_thumb.gif

post-99653-0-32527700-1387678987_thumb.gif

post-99653-0-13183500-1387679248_thumb.jpg

What's up with the front lip?

Looks a bit mangled?

must be an older pic, as you can see in one of the other's, it has a new looking black lip which seems to have replaced the mangled one.

  • 2 weeks later...

Im taking the engine apart :blink:and puting the origonal block /oil pump / head/ sump/ cpu/ coil packs/ balancer back on and -5s and dumps stying in and will be for sale in few weeks for

$18000 ONO

Thanks

PS :willing to swap -5s and dumps for origonal ones $1000 my way must be exellent condition and off 33 gtr

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...