Jump to content
SAU Community

Recommended Posts

Hi guys,

I've got some stuff thats been sitting in my garage which I'm hoping to get rid of.

1. Stock 2004 Honda Accord Euro wheels. They are 16" but I'm unsure of the offset or width. I'd guesstimate around 16 x 6.5 + 45. They use the same 5x114.3 bolt pattern and same hub diameter as Nissan, so they could bolt up to a Skyline or Silvia for cheap skid wheels or if you need to pass a defect. They are in good condition, one has a small gutter rash but nothing serious. 2 dont have any tires and the other 2 have really worn out tires. I'm after $250 O.N.O. for these.

post-39984-0-35593600-1387769284_thumb.jpgpost-39984-0-89612000-1387769287_thumb.jpgpost-39984-0-15850100-1387769291_thumb.jpgpost-39984-0-02211900-1387769295_thumb.jpgpost-39984-0-53045900-1387769298_thumb.jpgpost-39984-0-83462900-1387769303_thumb.jpgpost-39984-0-38037900-1387769306_thumb.jpg

2. A whole bunch of Earls and Speedflow fittings. All work fine but some are a bit scratched from spanners.

2 x brand new Earls -10 Straight fittings. One is still in the bag, the other one is taken out but never used
1 x barely used Earls -10 Straight fitting. I think i've tested it once, but didn't fit on my setup so I never used it. Its just got a few light scratches from the spanner.
1 x used 90 degree Speedflow -10 Fitting. It's been used on my old oil cooler setup, but then I changed from a sandwich plate to one with a thermostat so this fitting no longer fitted in.
3 x pretty used Earls -10 Straight fittings. These have a fair bit of spanner markings on them. Again, they are all from my old oil cooler setups. They all work fine, just don't look that great.

My camera kinda brings out every detail in the photos, but they dont look THAT bad in real life.

After $50 FIRM for these.

post-39984-0-34695300-1387769311_thumb.jpgpost-39984-0-02163900-1387769322_thumb.jpgpost-39984-0-62190200-1387769324_thumb.jpgpost-39984-0-29098100-1387769327_thumb.jpgpost-39984-0-82139800-1387769332_thumb.jpgpost-39984-0-75212000-1387769335_thumb.jpgpost-39984-0-47335200-1387769338_thumb.jpgpost-39984-0-34504400-1387769389_thumb.jpgpost-39984-0-78817600-1387769453_thumb.jpgpost-39984-0-95303900-1387769455_thumb.jpgpost-39984-0-74223800-1387769457_thumb.jpg

3. Stock S15 intercooler. I've always kept it in case of defects, but I've since sold my S15 and have no need for it. It comes with all brackets and all of the intake piping up to the intake manifold. I'm after $150 O.N.O. for this.

post-39984-0-02591200-1387769359_thumb.jpgpost-39984-0-21758700-1387769364_thumb.jpgpost-39984-0-66430500-1387769368_thumb.jpgpost-39984-0-83846100-1387769372_thumb.jpgpost-39984-0-90578900-1387769378_thumb.jpg

4. Stock S15 Fuel Pump. It came out of a JDM manual turbo S15 which had about 80,000kms on the clock. It was working perfectly fine, only reason I took it out is so I can upgrade to a bigger pump. I'm after $60 O.N.O. for this.

post-39984-0-82727400-1387769343_thumb.jpgpost-39984-0-49063900-1387769346_thumb.jpg

5. Stock S15 boost gauge sensor. Just the sensor, I don't have the gauge. $10 FIRM for this.

post-39984-0-12306900-1387769381_thumb.jpgpost-39984-0-61173300-1387769383_thumb.jpgpost-39984-0-37467700-1387769386_thumb.jpg

I'm located in Upper Coomera on the Gold Coast, QLD and I'm happy to ship at the buyers expense.

Cheers.

post-39984-0-65584300-1387769313_thumb.jpg

post-39984-0-88790900-1387769340_thumb.jpg

Edited by Goosy
  • 2 weeks later...
  • 2 weeks later...
  • 2 weeks later...
  • 2 weeks later...
  • 4 weeks later...
  • 3 months later...
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...