Jump to content
SAU Community

Recommended Posts

Hey guys, I recently bought this GTR and I'm not in a rush to sell it, I love it. I'm just putting it up for sale merely as an expression of interest, an exercise out of boredom if you will. If it sells, I'll move on, if not I'm completely happy to keep it :)

The engine was built by Gavin Wood on the Gold Coast, the mods are as follows:

CP Pistons

Eagle Rods

Tomei 270 cams

Springs/Retainers

N1 turbos with HKS actuators

Full custom tucked 3.5" exhaust and high flow cat made by Fabulous Fabrications (beautiful work) along with custom Hot/Cold cooler pipe.

Intercooler

Haltec Platinum Pro ECU

Bilstein/Eibach strut/spring combo

Cusco Swaybars

Cusco 1.5w rear diff, fully rebuilt and new diff bushing installed with newer (and slightly larger/stronger) R33 half shafts

Ikeya Formula front and rear upper control arms.

HICAS delete.

Desmond Regamasters in 17x10 + 20 wrapped in near new Federal 595 RSR's

The car made 385hp at all four on 18 psi and at a very rich tune of 11:1 up top. If I keep it, it'll be getting a retune shortly for more boost and a little less fuel, but it's quick as it is.

Aircon is cold, chassis rails are straight, no rust, this is a clean GTR :)

2 minor issues, the passenger side dash vent is missing (previous owner broke it trying to install a cup holder) and it needs new coil pack connectors and possibly coil packs. The coil issue will be taken care of prior to sale and I can chuck a vent in it, I just haven't found one for sale yet.

JerryGTR7_zpsb93a24ba.jpg

JerryGTR4_zps97c23603.jpg

JerryGTR10_zps6a90627f.jpg

JerryGTR2_zpsbc3c9bad.jpg

$21,000 ono

Will entertain the thought of trades, just depends on what I'm being offered but send your offers through anyway, it can't hurt!

0401029817

Link to comment
https://www.sau.com.au/forums/topic/437696-r32-gtr-forged-motor-mods/
Share on other sites

Since listing for sale the car has had
New coils (old coils were fine, misfire was being caused by a boost leak thanks for a faulty coupler)
Service in the last 100km
Brake rotors machined and pads linished, brand new pads
Replaced coupler to get rid of boost leak
The car is ready for its new home

It's an 89 Grant, yes I have a dyno graph floating around somewhere.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..   
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...