Jump to content
SAU Community

Recommended Posts

All items from my personal GTR 32. Located in Melbourne.

Air conditioner cooling unit - $220

Heating unit assembly - $240
Complete blower motor and fan assembly. Working well. - $150
Transfer case originally from R33 GTR - $220
Rear seat (back and bottom). Excellent condition - $120
Cusco strut tower bars suit R32 Front and rear. Avg condition. Scratches and paint chips - $180 pair
Weather strip retainers (L&R). Poor condition rubber strips, both suit restoring. Metal guides are excellent condition - $40 pair
Rear wiper motor - $90
GTR floor mats. Complete set. Avg condition, usual wear, no holes - $140 set
Interior carpet. Good condition. No stains, no burns. 2 small cuts for harness bolts - $120
Air con compressor, bracket, gas cylinder, and hose - $130

CUSCO springs (from Zero 2E coliovers) Cusco ID65 200 series. Spring rate: 11kg, Inner spring diameter: 65mm, Length: 200mm, Stroke: 100mm. Travelled 2000kms - $120 pair
GTR 32 front grill (silver) Good condition. Centre plastic clip missing - $110
Interior rear side trims (L&R) Excellent condition. All clips in tact, no tears in vinyl - $80 pair
Factory gauges for boost, water temp, battery. Fits into single din slot. Comes with loom plug - $110
Rear seat belts. Excellent condition. Barely used. Belts retracted into spool. Comes with fitting bolts - $100 pair
Climate control head unit. Good condition. All buttons work. Comes with loom plug - $90
Top cowl cover Fits under front wipers. Excellent condition, no damage - $40
Complete heater / AC ducting. Full kit includes behind dash and under carpet ducts - $30 set
Rear window lower outer moulding. No damage - $35
Rubber weather shields (L&R). Heavily worn but still working - $30 pair
Front door outside moulds (L&R). Poor condition. Suit painting - $40 pair
A-pillar trims (L&R) 3 small holes in drivers side for pod gauge fitting - $40 pair
Rear parcel shelf (original). Good condition - $40
Original Nissan brake lines and used Bendix pads - $40
Nissan standard CAM gears - $40
Oil catch can. Never used. Looks about the size of 500ml - $20
Rear seat firewall plate. Avg condition. Some scratches - $35
RB26DETT oil air breathers and joins - $20
Antenna booster - 12V amplified New. Boosts weak FM radio signal (10dB gain). Problem particular to R32's where the antenna is built into the windscreen - $20
Under bonnet trim Avg condition. No damage, just needs a clean - $20
Sun visors (L&R) Avg condition. Need a clean - $25 pair
Boot trim, carpet, and board Good condition. Left side trim torn slightly. Holes cut in side trims for struct tower bar. Selling as set - $25 set
Rear window wiper -$20
Nissan spare jack (original) - $15
Child anchor points and brackets Fitted onto rear parcel shelf during compliance process - $15
Interior roof lining. Excellent condition. No damage - $20
Pics available for all items..
Link to comment
https://www.sau.com.au/forums/topic/437715-random-parts-r32-gtr/
Share on other sites

  • 2 months later...

Hi just wondering if you are able to ship the rear windscreen moulding?

If you are referring to the rubber moulds, these are heavily worn. If you are talking about the hard plastic moulds, then yes I can post within Aust.

Allow $15 for postage

  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
×
×
  • Create New...