Jump to content
SAU Community

Recommended Posts

Tyres different rotational circumference to the rear tyres, or the steering wheel sensor (behind steering wheel) needs realigning.

(EDIT: the differance in Tyre profile will only affect vehicles with ABS and Attessa and won't affect those with Hicas as it get its speed reading from the gearbox)

MEGA

Thanks for your help Mega.

The 2 front tyres that I changed are still the same size as my last 2 front tyres though, and the HICAS never appeared back thenso i dont think that could be the problem or could it? My front tyres are 225's and my rears are 265's.

Though i think it could be the steering wheel sensor that you speak of, since my mechanic did have to open up my steering wheel the other day.

Is it an easy job to realign the steering wheel sensor?

If so can you tell me what i need to do or should i just take it to a workshop?

Regards

Its not the 225 or the 265, its the profile which will be 50, 55 or 65 etc that I was refering too though. (although this seems to affect vehicles equiped with attessa more than ones with hicas though, sorry my bad!)

But if your mechanic removed the steering wheel then he must have done a wheel alignment and straightened the steering wheel by removing it and changing the position on the spline, this will be fine on any other car but not on one with hicas, the poor car thinks its going round in circles hence the error code.

As for fixing it, maybe do a search as it has been covered before with pictures and descriptions on how to realign.

There is no easy fix if its the tyre profile as the car will be getting two different speed sensor readings from the front to the back, so basically need to change the tyres to the same profile as the back to remove the error in the system. Hicas has two speed settings fast and slow, and this changes the system to suit fast corners or slow ones, if there is a marginal differance between the two speed sensors (front/back) it will shut down hicas.

MEGA

Ok. I have this problem like this. Could just be conincidental that it's happened when you changed the tyres.

This is the problem I have with my hicas. If I drive on the M1 (Brisbane - Gold Coast) to about the Strawberry Farm half way down the coast (say 30/40ks?) the light comes on.

I've had heaps of problems with my hicas since purchasing the car. Once it was realised that there were wires disconnected, it was all fixed. Then driving up to the sunny coast one night the light came back on. I was fuming.

Ended up getting the car put onto the diagnostics machine and it said that there was a fault in the sensor in the steering wheel.

Basically to put it simply, there is a sensor in the steering wheel that can loose contact sometimes. This happens if the wheel is held straight or moved slightly for a long period. I was told this sensor was about $300 to fix but seeming it only happens on the highway (when hicas comes into effect) I didn't bother getting it fixed because I dont personally do highspeed lane changes and drastic steering movements on a straight road.

If you can, try and get someone to plug your car into a consult machine and get a report printed out on what fault is coming up in the diagnostics.

Ylwgtr2 is right the chances that someone has the consult is slim, on board diagnostics is the best way and its free too.

Nothing is this conincidental if your playing with the steering wheel position as is the things the hicas rely on. The speed sensor and the steering angle sensor are the eyes and ears of the hicas system.

MEGA

If it is the same problem as the Z32 i've got then it could most likely be the hicas system acting on its own due to something being aligned incorrectly as my steering is slightly to the left when i travel along highways the hicas thinks i'm constantly turning and it recognises this and turns itself off. Therefore basically /hopefully all u need to do is fix whatever is causing this.

Sorry Conan I have led you down the garden path, the steering angle sensor is out or not working properly because the only thing that works off the individual wheel speed sensors is the ABS system and attessa equiped vehicles (GTR's and GTS4's) and yours being a R34 GT-T it will be the sensor behind the steerig wheel that is out of alignment.

The hicas system gets its speed reading from the gearbox and this won't change no matter what profile tyre you use.

Take it back to the mechanic to fix it or ask him if he moved the position of the steering wheel, if he has tell him it needs to be aligned or put back to neutral position.

I hope you see this before you change try and change tyres.

Sorry if I caused any trouble again!

MEGA

Sorry Conan I have led you down the garden path, the steering angle sensor is out or not working properly because the only thing that works off the individual wheel speed sensors is the ABS system and attessa equiped vehicles (GTR's and GTS4's) and yours being a R34 GT-T it will be the sensor behind the steerig wheel that is out of alignment.

as Mega said .... its the sensor ... (100%)

i have the same problem ... with my R34 GT-T .. its still there .. coz my car is converted to ( left hand ) and the steering box am using now is for nissan maxima ... which has no sensor ...

so .. the hicas coms out on highways ... only ..

check u'r sensor ... if its pluged ... or if somthin wrong with it ... ( hope its only unpluged )

good luck ...

Thanks OMRAN.

But will it be of any risk if i dont get the sensor fixed?

Can HICAS screw me up if i constantly drive on the high way?

No it wont harm/risk anything as all it does is disables the hicas system and stores an error code for consult or diagnostics to retreive at a later date, which means that after 100 your car will act like a normal car that has 2 wheel steering.

I have attached some pics to help you understand the hicas system a bit better, you might find them interesting. (though they are for nissan's turbo Z they are the same in principle)

MEGA

Thanks OMRAN.

But will it be of any risk if i dont get the sensor fixed?

Can HICAS screw me up if i constantly drive on the high way?

i think .. u can read what MegaGTS4 have posted .... .. i think he have more experiance in hicas ... then me .. :D

and .. what i know .. is that it wont f*&^ up u'r hicas ....

and as Mega said ... u will be driving with 2 wheel steering ... ( thats am not sure about ... )

i'll try to see it my self .... if the hicas light go's on .. i'll stop the car .. and move the steering all the way ... right .. to .. left ... and look at the rear wheel .. if it start moving or not ... ( its a slight move .. 4 degrees only )

thanx alot MEGA ... u'v been helpfull .. :) ..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah and hence my ghetto way of slamming the brakes, get the ABS to cycle, rebleed seems to be a sensible workaround.
    • Hey! Happy to help. Nothing inherently wrong with the adapter, it's more so with Brett Collins himself. He gave me a lot of incorrect information when I was in contact with him and was extremely rude when I challenged him. He stated I could not use any aftermarket twin plate clutches except for his own, not to use the dush shield, bla bla bla and it was all BS.  Collins stated to cut roughly 14mm's off the housing, I took off 15mm to make room for the dust shield. I would confirm with whatever adapter manufacturer you're using. 
    • There's plenty of OEM steering arms that are bolted on. Not in the same fashion/orientation as that one, to be sure, but still. Examples of what I'm thinking of would use holes like the ones that have the downward facing studs on the GTR uprights (down the bottom end, under the driveshaft opening, near the lower balljoint) and bolt a steering arm on using only 2 bolts that would be somewhat similarly in shear as these you're complainig about. I reckon old Holdens did that, and I've never seen a broken one of those.
    • Let's be honest, most of the people designing parts like the above, aren't engineers. Sometimes they come from disciplines that gives them more qualitative feel for design than quantitive, however, plenty of them have just picked up a license to Fusion and started making things. And that's the honest part about the majority of these guys making parts like that, they don't have huge R&D teams and heaps of time or experience working out the numbers on it. Shit, most smaller teams that do have real engineers still roll with "yeah, it should be okay, and does the job, let's make them and just see"...   The smaller guys like KiwiCNC, aren't the likes of Bosch etc with proper engineering procedures, and oversights, and sign off. As such, it's why they can produce a product to market a lot quicker, but it always comes back to, question it all.   I'm still not a fan of that bolt on piece. Why not just machine it all in one go? With the right design it's possible. The only reason I can see is if they want different heights/length for the tie rod to bolt to. And if they have the cncs themselves,they can easily offer that exact feature, and just machine it all in one go. 
    • The roof is wrapped
×
×
  • Create New...