Jump to content
SAU Community

idiot...

LOW25T

By LOW25T,
in General Maintenance

 Share

Recommended Posts

Guest two.06l

Guest two.06l

Posted
Posted
Ummm, i accidently snapped one of the wheel studs after changing my brake pads, is it safe to drive around in temporarily (with the remaining 4 studs), untill i get it fixed???

think about it this way 1/5 of the studs is 2/5 more dangerous, drive it with a 3/5 less throttle in 4/5 of a week to get it fixed before your car becomes 5/5 of the scenery.

Link to comment
https://www.sau.com.au/forums/topic/44081-idiot/#findComment-900767
Share on other sites
[WLDCRD] Mentor

[WLDCRD]

Posted
Posted

well, i guess it could depend on the condition of the other 4. I did the same thing once and i actually got pulled over and got a defect for it (amongst others) albeit it was a canary yellow V8 commodore which stood out like dogs balls haha Safety-wise, its probably not the best idea as the wheel could potentially fall off (worse case scenario) but if you are desperate like i was, you can as long as you dont do anything stupid. Best advice is to get it fixed asap.

Link to comment
https://www.sau.com.au/forums/topic/44081-idiot/#findComment-900773
Share on other sites
[WLDCRD] Mentor

[WLDCRD]

Posted
Posted

yeah i got mine welded on....but it snapped off again later. I must be too strong haha make sure if you get new ones they are the right length....cos my one ended up being longer than the others and the nut didnt fit. Luckily i had 50million of the buggers lying around. Its no big drama and it shouldnt cost you much. If you just twisted it off the hub thingy, you can reuse your original bolt.

Link to comment
https://www.sau.com.au/forums/topic/44081-idiot/#findComment-900801
Share on other sites
predator Grand Master

predator

Posted
Posted

one less won't kill you..

my other car i found out only had 3 studs on each wheel (and it only had 4 to start with).. and i've been driving like that since i got it for around 15,000km with no probs. If the others are done tightly i don't think the wheel is going to fall off.

But yeah, get it fixed if possible :D

Link to comment
https://www.sau.com.au/forums/topic/44081-idiot/#findComment-901429
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • GTSBoy
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By GTSBoy · Posted

      I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
    • GTSBoy
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By GTSBoy · Posted

      I'd say it's a fair bet that the feed and return fluid lines will be in different enough spots that you would need to come up with a way to cut the originals short and adapt with new hard line adaption or braided teflon hoses or somesuch. But really, you have the car, you have the photos of the DMAX rack - you should be able to go out there and see for yourself whether they're in the same or different spots.
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      I've been doing some looking around and honestly was just considering throwing a new rack at it. I saw that the dmax silvia rack bolts up into the 33 with the silvia bushings but not sure if the high pressure lines will sit in the correct spot. I believe other version of the 33 rack are the same/similar to the racks that can be opened up without as much fuss so I assume the dmax rack would fit but any ideas?
    • GTSBoy
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By GTSBoy · Posted

      I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
×
×
  • Create New...