Jump to content
SAU Community

Recommended Posts

Hi All,

Brand new Nismo Intercooler piping kit to fit BNR34/BCNR33, only taken out of the box for pics.

Planned to fit this along with nismo Intercooler, inlet pipe etc; to my car which has been sold. All other items apart from plenum have been sold. Asking 750ono

post-135234-0-73641500-1404613105_thumb.jpgpost-135234-0-77131500-1404613119_thumb.jpgpost-135234-0-58378600-1404613132_thumb.jpgpost-135234-0-68825800-1404613148_thumb.jpgpost-135234-0-11476800-1404613198_thumb.jpg

post-135234-0-87155900-1404613092_thumb.jpg

post-135234-0-47375100-1404613209_thumb.jpg

Thats cheap! :O this kit is the one i always wanted but it was $1800 to buy, wont last long at this price i would say

i now have a single turbo so wont suit me now

GLWS!

Edited by NIS.26L

Errr hey mate, just FYI - Two of your pics are from the Nismo inlet piping kit, which is part of a different kit compared to the intercooler kit :-)

  • 2 weeks later...
  • 2 weeks later...
  • 2 weeks later...
  • 2 weeks later...
  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...