Jump to content
SAU Community

Recommended Posts

Specialised Guard Rolling

Professional Mobile Guard Rolling Service

ph: 0412999682

James Bailey

[email protected]

$60 a guard

$100 for two

$200 for all four

Highly reccomended by myself. He rolled the front guards on my Skyline and i have no complaints whatsoever.

Link to comment
https://www.sau.com.au/forums/topic/44662-guard-rolling/#findComment-912660
Share on other sites

All depends on the wheel size.

I run 18x10 rear wheels on an R33 GTSt with 265/35 rubber, and i've got my coilovers wound....pretty much all the way down, there's still some more left, but i don't want to go lower. My tyres are tucked up inside the guards.

My main issue was with the 9" wide fronts when on full lock coming up gutters. Sorted that out, by getting the guards rolled. ALl good now.

Link to comment
https://www.sau.com.au/forums/topic/44662-guard-rolling/#findComment-913989
Share on other sites

  • 3 years later...

Well, digging up an old thread but at least the search button works.

I know guard rolling can be bad for cracking paint, but i'm sure cutting tyres with metal at 100km/h is worse...

Has anyone else got any decent recommendations on a place to do it? I used QuickFit in Phillip on my subie and they didn't do the best job. Didn't even appear to heat up the guard first....

Link to comment
https://www.sau.com.au/forums/topic/44662-guard-rolling/#findComment-3718758
Share on other sites

Jax Quickfit in Fyshwick did my fronts (The old Strathfield Car Radio) and it was fine. I hear they're about $60 a corner these days.

Jax Quickfit did the GTST and it worked a treat, paints fine and it allowed me the wider tyres to fit legally within the guards now. I didn't have a choice, I had a race the next day and wouldn't have passed scrutineering with my new tyres. Race or not race?? Easy choice :D and it was a success.

Link to comment
https://www.sau.com.au/forums/topic/44662-guard-rolling/#findComment-3720408
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...