Jump to content
SAU Community

Recommended Posts

Time to move on, so here it is :

I've had this car for 5-6 years, the previous owner spent well over 50k on this build just before moving over seas and me purchasing it, and I've put ten of thousands into it since then..

engine was built by Nisspeed in Adelaide and now has 35k kms on it. Runs 600rwhp on 98 @ 1.8bar

HKS step2 2.8 stroker, full counter crank and rods kit, CP pistons.
Brand new head from Nissan, Jun 272 in and ex cams, 10.8mm(?) lift, special retainers and all the jazz needed to support the cams and high revs, heads extensively ported.
Big dollar hypertune plenum and single throttle body setup
Custom alloy breather tank etc
Jun oil pump, N1 water pump,

ATI balancer

Trust sump extension.
Garrett TO4Z turbo and big Turbonetics external gate
OS Giken 2 way front diff
OS Giken cross mission 5spd gearset with input shaft 800+hp rated, and Billet centre plate, Less than 5000kms old
Nismo Super Coppermix spec C twin plate, less than 5oookms old, gearbox, clutch and rear diff just cost $10k plus
Nismo GT pro 1.5 rear diff less than 5000kms old
wastegate plumbed back into HKS 4inch exhaust
Huge alloy PWR radiator,

disgustingly thick Trust Spec R intercooler 160mm
Fuel system to cater for 1000hp+, in boot setup as in pics, new fuelab 1500hp variable speed pump, all E85 compatible
1000cc HKS injectors,
HKS fuel rail 11mm

Teflon braided fuel lines
splitfire coilpacks
Motec M800 ECU + Loom + Sensors

HKS coilovers
V-Spec Brembo's rear, K-Sport 8-pot 356mm fronts with new rotors
Midnight purple paint in excellent condition. Will try and get some pictures with better light to show off the purple.
Excellent condition original interior with almost no wear in the usual places (seat bolsters, etc)

Custom Air/con system, to fit with big intercooler, radiator and oil cooler

Fullrace ETS pro Attessa computer. Complete stand alone unit that enables you to control the 4wd from 0-50/50 split and RWD mode.

Series 3 Zenons
Silly money spent NO EXPENSE SPARED ON THIS BUILD. $38k ono

Richard 0411861466 WA

post-48287-0-51161200-1411891955_thumb.jpg

post-48287-0-80569200-1411892029_thumb.jpg

post-48287-0-45769700-1411892076_thumb.jpg

post-48287-0-18106200-1411892140_thumb.jpg

post-48287-0-46169900-1411892180_thumb.jpg

post-48287-0-88822400-1411892242_thumb.jpg

post-48287-0-01830500-1411892687_thumb.jpg
post-48287-0-13585100-1411892846_thumb.jpg

Edited by tricstar
  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/449131-midnight-purple-r33-gtr-28l-600rwhp/
Share on other sites

  • 2 weeks later...
  • 2 weeks later...
  • 2 weeks later...

Guy got a bargain. Would've liked a bit more. But we're only talking a few grand. Sorta glad it's done, now I can concentrate on other things.

Got a GTSt that I'm striping out for a track car, so I'm not gone.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...