Jump to content
SAU Community

R33 S2 Gts-T Engine Dies Randomly, Won't Start, Cas Replaced Issue Continues

Links

By Links,
in General Maintenance

 Share

Recommended Posts

Links Veteran

Links

Posted
Posted

Afternoon all,

Quick background:

- 1998 R33 S2 GTS-T with minor mods - brant security alarm fitted.

- 120,000 kms

Summary:

- Engine was losing power (would hesitate then pick up) at 1,500 - 2,000 RPM and then died suddenly after having been doing this for a few weeks.

- Electrical's continue to work and immobiliser not kicking in (engine light on), engine will turn over but not start immediately after.

- Starts again after 20 - 30 minutes and runs for maybe 5 minutes at most before dying again

- Fuel pump flowing ok and primes when power turned on, mechanic checked and fuel flow ok.

- Checked diagnostics and returned 11 CAS code (need to check again now it's died again)

- Replaced with second hand R34 NEO GTT CAS from JustJap, mechanic says car ran fine for "30 minutes"

- Picked it up and same issue occurred within 200m where engine died and wouldn't start.

Note:

- Coil packs / spark plugs were replaced approx. 10k ago

Looking to get some assistance in understanding what the issue may be and how best to isolate.

Consideration:

- AFM

- ECU

- Wiring issue

- Earthing issue

- Immobiliser

- ?

Links

Link to comment
Share on other sites
Links Veteran

Links

Posted
  • Author
Posted

Afternoon,

Idle prior to stalling was fine, no lumpiness or change in tone.

Quick update:

- have disconnected AFM to see if it would start in limp mode, engineer turns over but no starting.

- checked CAS is connected ok and rotated to see if any difference. No change.

- won't start at all now.

Next steps:

- purchase consult cable so we can see what the sensors are showing

- going to replace field filter and check fuel pressure to make sure issue isn't a blockage.

- will also look at testing CAS again and then start to check electricals and also lines to make sure no leaks etc

Link to comment
Share on other sites
Links Veteran

Links

Posted
  • Author
Posted

Update:

- Fuel Filter replaced, no issue with fuel as pushing out when pump priming

- ECU is now showing 55 (no error) and the engine still won't start.

- Next step is to check the wiring and see if there is anything other things broken

Link to comment
Share on other sites
Kane_R32 Experienced

Kane_R32

Posted
Posted

Does it just crank, and not even sound like its trying to fire?

I'll just throw these out there:

1) second hand CAS could be faulty

2) disable alarm if possible to eliminate 100% (seen faulty alarms still allow reds depending on set-up)

3) spark issue?
4) timing issue (could've jumped a tooth or stripped ribs on the belt? Worth having a look to see if the cams gears /belt spin while cranking.

Link to comment
Share on other sites
Brady_033 Apprentice

Brady_033

Posted
Posted

Sorry to Hi-jack the post Links haha :whistling:

But I'm currently having the same sort of problem with my S2 33!

Car will die when it gets warm (bit under half temp on gauge) have tried two cas's and a different afm. When car dies it will crank but wont fire but if you leave the car to cool down it starts first turn and will run until it dies again..

Link to comment
Share on other sites
defari Grand Master

defari

Posted
Posted (edited)

seriously ditch the brant alarm.. biggest pos... they came factory in my sti... extremely annoying when they are on their way out.

i have the same prob... car is fine when cold.. when its hot it wont start... this is the alarm/immobiliser failing...

there has been some stories of the brant alarm immobilising the engine whilst freeway driving..

Edited by defari
Link to comment
Share on other sites
Brady_033 Apprentice

Brady_033

Posted
Posted (edited)

seriously ditch the brant alarm.. biggest pos... they came factory in my sti... extremely annoying when they are on their way out.

i have the same prob... car is fine when cold.. when its hot it wont start... this is the alarm/immobiliser failing...

there has been some stories of the brant alarm immobilising the engine whilst freeway driving..

Do you think this could be my problem also? I have a Mongoose M80

Edited by Brady_033
Link to comment
Share on other sites
Links Veteran

Links

Posted
  • Author
Posted

Afternoon all,

Thanks for the feedback.

Update:

- Have ordered ECUTalk to be able to look at what is being read from the sensors.

- Based on the ECU returning 55 (all is ok) I am planning to look at disabling or removing the Brant alarm so that we can rule that out.

Given the behavior and everything seems to be ok in general, i'll give the alarm the next focus and see where we go to from there.

Link to comment
Share on other sites
75coupe Grand Master

75coupe

Posted
Posted

The coolant temp sensor can do what your describing, i had to replace mine in my s2r33 as well... It showed an error on the pfc hand controller as well so consult should pick it up

Link to comment
Share on other sites
Links Veteran

Links

Posted
  • Author
Posted

Morning all,

Update in the last couple of days. Received consult cable hooked it up, ecu is showing 55 so no errors being reported.

Turned the car over and it started first go - left it to idle for a while and then have taken it up / down the road while monitoring. Everything was working ok which means I now need to consider heading out for a few longer drives.

Brant alarm keypad isn't lighting up so my thoughts are that there is still an issue and it's the alarm however i'll deal with it shortly.

Thanks everyone for your feedback. Still not confirmed what the root cause was however will see how it goes.

Links

Link to comment
Share on other sites
  • 3 weeks later...
Links Veteran

Links

Posted
  • Author
Posted

Morning all,

Thanks for the prompt as always good to close out a post.

  • After plugging in a consult cable and tracking the data when the car died the ignition was stopping. I called a Brant alarm technician to come and have a look.
  • Keypad immobiliser module had a faulty relay which was triggering when it over heated - this was causing the relay to trigger and cut the ignition.
  • Crank angle sensor was also replaced which has addressed the loss of power issue so all back on the road.

Links

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • SLVRBAKSLPZ
      In Need if Help with Signal lights: Constant on

      By SLVRBAKSLPZ · Posted

      I've had these LEDs and a LED EP34 flasher relay in the car since 2020. No fuses were popped either. I'll multimeter and clean off the tarnish tomorrow. From how the lights were acting after I diddle the stick make me lean towards a stalk problem.
    • GTSBoy
      In Need if Help with Signal lights: Constant on

      By GTSBoy · Posted

      Are you sure you can use LEDs in the indicator lamps? On a car that old? It doesn't work on many old cars because the indicator relay can't cope with the wrong impedance out at the lamp positions and the LEDs will happily light up even with minimal current flowing through the indicator relay. And when I say "indicator relay" I mean the flasher, not a relay relay. Beyond that, I would say that you have caused yourself a wiring fault and that you would be well advised to work through the wiring diagram and the actual loom with a multimeter.
    • SLVRBAKSLPZ
      In Need if Help with Signal lights: Constant on

      By SLVRBAKSLPZ · Posted

      Did some more messing around with this issue. I think the stalk is the problem. i wiggled it around a bit. When i went to put the signal up for a left turn, all the signals blinked lol. I'm gonna try and clean the tarnish off the copper and see if that works. this still doesnt explain why the left side/fronts are constant on ACC/On after i pulled the stalk. may be a ground from the stalk thats causing it. IDKkKkKk. I'll report back
    • GTSBoy
      Hypergear Turbochargers and High flow Services Development thread

      By GTSBoy · Posted

      Impressive power for a small rear housing. 👌
    • SLVRBAKSLPZ
      In Need if Help with Signal lights: Constant on

      By SLVRBAKSLPZ · Posted

      Hello, Has anyone experienced their signal light being constantly on when parking or headlights are on?   I'm putting my car back together after painting. I didn't pull out the hole chassis harness. I hooked up the chassis harness in the bay along with semi-installing a new ecu harness.   I put power to the car today to play some musicand check on thing while I worked. I noticed when I put on the parking lights that the left rear signal was constantly on. I thought for whatever reason. All the signal light needed to be install. The rear left signal did turn off after all the other signal bulbs where installed, but now the other 4 are lit. The left 2 are brighter than the right. I noticed that if u pull out the front left bulb them the left rear turns back on. Strange. Hazards work fine. Activating the signal from the stalk works. I unplugged the signal stalk power to see if that may have been the issue. Removed the fuse for the signals and they stay on constant but not blink.   I have LED 194/T10 bulbs. They're not switchback. Things worked as normal before I took thing apart and painted. The only new things I wired were two removed leads to my fuel pump relays.   Could it be the stalks? I bumped them plenty while working. Just from today I assessed them good and no flickering from contact on so it's hard to say it's the stalks.   The issue somewhere in the chassis harness?    
×
×
  • Create New...