Jump to content
SAU Community

Recommended Posts

Hi all,

Just throwing a few things up for sale. Will be updating/adding more over the next few months :)

1. Hypergear Highflow- $650 ono

One of Stao's PU Highflows which is a direct bolt- on turbo for RB25s. Looks totally stock when bolted up.

Utilises the stock compressor housing so that you can use your existing intercooler and intake piping.

Bolts up to standard/aftermarket dump pipes.

Stock water lines can be used with some minor bends/adjustment.

Comes with alloy intake pipe, braided oil feed line, stock compressor outlet elbow, dp gasket and oil drain fitting.

This turbo made 287rwkw on my R33 at 19psi. Tuned by Toshi with S15 480cc injectors, 3" exhaust and return-flow cooler!

It has served me very well, only upgrading to chase more power.

post-55684-14166278159715_thumb.jpg

post-55684-14166278444348_thumb.jpg

post-55684-14166278898909_thumb.jpg

2. GTR bov - $50 ono

Stock GTR bov. Speaks for itself. Larger diameter- flows more air!

3. Stock RB25 R33 turbo- $200 ono

Had less than 100,000km when removed. In good condition.

4. Suede steering wheel - $50 ono

Good condition, a little worn in some areas. Note: Not a genuine OMP

post-55684-14166281586849_thumb.jpg

5. Stock R33 ABS diff- $250 ono

Stock diff, not shimmed or messed around with. Was getting a bit loose when it was removed but could easily be shimmed to toughen it up again!

post-55684-14166282416561_thumb.jpg

Most items located in Dubbo NSW. But can arrange postage on items or can take them to Sydney next time I am down.

PM for any questions!

If anyone buys the high flow and is looking to change the rear to an OP6, I will have one available as I'm going to use a 21U for a little more response. Great turbo otherwise.

Good luck with the sale

  • 2 weeks later...

Adding this to the thread- 3" bellmouth dump pipe section.

I had to make a new dump pipe so I have this bit for sale.

Would be of benefit to anyone wanting to make their own downpipe (this is the hard bit to make!)

5-Bolt nissan flange. 3" mild steel.

$50 ono

Cheers

post-55684-0-44880300-1417830164_thumb.jpg

post-55684-0-27002300-1417830171_thumb.jpg

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If there's enough meat in the housing where you want to put the M12 adapter, then do it, but be aware that if/when you f**k that up you'll probably be repairing it before doing anything else. I'd just drill it out and tap ina 1/4" thread. No need for rocket surgery when the next most obvious thing will do. You could throw a 1/4 x 1/8 bush in there and use the same fitting you intended to use.
    • Is the only issue that the oil catch can is getting filled on hard runs? I'd be thinking more about oil control issues rather then the head lifting, especially as you aren't seeing spiking in the coolant pressure.  Do you need restrictors in the head, or better drains from the head? Does the sump need venting to the catch can?
    • Tried to make 1/8npt threads into compressor house of the turbo for my EBC. Threads got fu#ked and ended up with and elongated hole, so I do have good amount and nice threads 90% of the hole but 10% I only had 1-2threads there and rest of it is flush on that side of the hole.. So my idea is to do M12 x 1.25 to AN4 with braided lines instead of 1/8npt to 4mm vacuum silicone hose.  and hopefully get a better thread. M12 is quite big and AN4 is a little bit bigger than 4mm (4.9mm inner diameter braided PTFE hose). but this should work. Thoughts? Otherwise I will weld and adapter onto the turbo.   
    • Looks great, I hope everything is working well after all that time!
×
×
  • Create New...