Jump to content
SAU Community

V36 350Gt Coilover/lug Pattern/offset/supercharger Options?

350_GT
 Share

Recommended Posts

350_GT Apprentice

350_GT

Posted
Posted

Just got my 07 350GT here in New Zealand after moving back from the USA. Has 70k on it, Nismo Struts/Springs, Cusco Brace, 19" Enkei Factory Wheels. Now I have a friend who can get me 20% off on a Stillen SC kit, but it is super expensive for shipping. Also looking for a nice set of coilovers, and the lug-pattern and offset of the stock wheels. Here is a pic as it sits now, quite flush but not exactly how i want it to sit.

8D383B36-BF4C-4A1C-81FE-82C12DD52C94.jpg

026774E6-8648-48ED-8AB1-370406BD9D8E.jpg

BB8E4BBA-2099-4B2C-A6B8-98955537B217.jpg

Any input would be great thanks

AsM Rising Star

AsM

Posted
Posted

I have a set of very low RS-R Black 1 coilovers from my V36 that would suit it beautifully. Going cheap too.

^^how much are you after and what are the specs? pm me if you like thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • djr81
      R32 update from 1990's spec.

      By djr81 · Posted

      So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • djr81
      RB26DETT Sketchy boost mod?

      By djr81 · Posted

      Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...