Jump to content
SAU Community

Recommended Posts

  • 3 weeks later...

Did you work out what the funny sound Is when it starts spooling up I drove there from Newcastle to have a look and couldnt come up with the cash in time I would of msged him about a week after you got it..........

Would you be interested swaps for a r32 4 door sedan with a lot of money spent on it and a lot of engine work

Or a genuine Vl Calais

Or cash price

Well I have my other 4door, which was written off, which was pretty clean & have swapped over coilovers, rear camber arms, tie rods and stuff. Went through the stereo & replaced headunit. And put my s2 rear lights on it. Changed my seats over and various parts of the interior to clean it up. Replaced climate control module & instrument cluster bulbs for leds, & now all lights on dash work, & i tinted the windows. There's other little bits too, just trying to get it to how I had my other one. Only thing left to do now is put my motor into it. Just want to make sure eveything is sorted first.

R32 skyline sedan

Rb20det

Hd clutch

Power FC

550cc injectors

Z32 afm

Turbo smart boost t

Power spirit 3076 turbo

Pod filter

Front mount Intercooler

Stainless steal dump pipe

Walbro fuel pump

silicone radiator hose

Nismo thermo stat

K&n oil filter

New fuel filter

New battery

Spitfire coil packs

Gtr fuel resister

Boost gage

Turbo timer

Digital speedo

New thrust bearing

New spark plugs

Cusco Adjustable rear camber arms

Cusco adjustable front camber arms

Drift works hicas delete kit

subframe c lock collars

Coilovers

Smoked blinkers

Bonnet cut to look like gtr bonnet with carbon n1 lip

Vertex body kit

Few other things

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...