Jump to content
SAU Community

Lfting Points

Scantr0n

By Scantr0n,
in General Maintenance

 Share

Recommended Posts

Scantr0n Newbie

Scantr0n

Posted
Posted

Hello guys and gals, new to this site and wanted to ask a silly question since i recently got a r34 vspec. Im looking at removing the front bumper (is there a thread for bumper removal) to install new intercooler. Wondering if you guys know the lifting points on the car so i can place my jack stands on the correct spots. Please let me know if you can help me out. Thanks alot for your help :):yes:

Link to comment
https://www.sau.com.au/forums/topic/454595-lfting-points/
Share on other sites
  • 2 weeks later...
Kinks Grand Master

Kinks

Posted
Posted

chassis rails are quite soft, I have bent them before. With a block of wood to spread the load you should be OK but make sure your lifting setup is solid and not going to fall off the jack.

Axle stands - Crossmember at the front, subframe at the back. Those will NEVER move :)

Link to comment
https://www.sau.com.au/forums/topic/454595-lfting-points/#findComment-7502290
Share on other sites
StretchGSK Enthusiast

StretchGSK

Posted
Posted

Dont use the chassis rails there are 4 points on the sils that have a lump for the jack stands to sit in nicely and are a solid point, using the cross member is fine aswell but rails will bend

Don't see a way to use these without crushing the surrounding "seams"

Link to comment
https://www.sau.com.au/forums/topic/454595-lfting-points/#findComment-7504250
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Looking for a part number for this part here

      By Duncan · Posted

      So....to find any R chassis part number, get your VIN (will be something like ER33-xxxxxx for you) and go to: https://www.amayama.com/en/genuine-catalogs/nissan and enter it. From there you have access to a web version of Nissan's part system, FAST. It is a bit tricky to get used to, so maybe have a shot and post up what you think.  You can also search by general model but note in some cases your car might have different options so VIN is safest.  On diagram 211 I got 14075-75T16 for Connector, Water Hose If I search for part 14053‑21U10 that you posted, that is also a water hose but not the one bolted to the plenum and 14075‑04U00 is the fitting where the water hose goes into the block.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Yeah now we are talking I much prefer coolers in the front middle because it lessens the chance of a small bump to a corner stopping the whole event. I was thinking the AT cooler can move out of the radiator, delete the AT/engine coolant interwarmer and mount a separate cooler with a thermoswitch somewhere further back as is common in racing, that would be one thing. Beyond that, the engine oil cooler is an obvious one to move to the wheel arch, potentially one on each side, but unused space is an issue. I did have a earlier pic with the bumper off but it doesn't show how busy the corners are: DS is full of the auto driving sensors and PS is totally fully of windscreen washer fluid reservoir But ultimately I was hoping to keep the AC, and the water/air heat exchanger is fundamental so it is not just the radiator that needs to be in front BTW here's airflow to the rad as it ran at the track (one horn is gone now and I'll remove the lights next time):
    • turboedsloth
      New Wasteland Wa Topic

      By turboedsloth · Posted

    • V35_Paul
      Infiniti Q60 Navigation Update

      By V35_Paul · Posted

      your right the maps for Australia came out in 2017 but are 2010 maps. i got the updated maps SD card put it in and it was the same. Same maps in my Brothers Nissan Patrol. 2020 i think his car is
    • silviaz
      Returning after a long time!

      By silviaz · Posted

      Yeahhhh, the costs have killed me. Spent more than the cost of an engine rebuild and it most mostly servicing and a tune lol.
×
×
  • Create New...