Jump to content
SAU Community

Recommended Posts

Hi all,

I have a few bitz from a Rb25det race engine that i never completed & it has since

been laying around my shed for a while.

I need to move them on.

List is as follows,

1- Rb25det Stage 2 Race head.

I have had this built by a professional shop and it is still brand new wrapped up in plastic.

Head is off a series 2 R33 Gts-t & suits any Rb25det bottom end.

Chemical clean

Preasure & crack tested

K-line guides,multi angle valve job

Replaced super tech seals

High lift spring & retainer kit with 9.5mm lift caability

260cfm Race port for maximium flow.

Included in the price is a pair of Tomei Poncams.

Inlet is 256mm with 8.5mm lift

Exhaust is 264mm with 8.5mm lift

Also included in the packege is an adjustable Hks cam gear.

With this Poncam set up you can still retain the factory VCT which is worth using as it will help with boost coming on around 500rpm earlier.The Poncams will give you greater low to mid range torque.

This head is brand new,the Tomei cams and Hks cam gear have done around 1,200klms in a previous set up,& are in as new condition.

Complete head set up with Cams & adj cam gear $2600

2-Rb25det Stroker bottom end 2.7l.

*Components have been in workshop sitting around & has some surface rust on Block,

small amount on crank and some surface rust on the rods (as pictured)

The block is Rb25det that has been mechined to 87mm

The block was originally mechined at Jack bros Racing in Slacks creek along with the Rb26 Gtr crank & girdle.

Pistons are JE from memory..87mm. New Total rings were fitted.

Rods are Crower.

After a small engine falure on the dyno (bearings) the bottom end was then stripped

down and re machined by JHH Racing where it has since been sitting around in my shed in its current unassembled state.

Odviously you will need to freshen up the bits again.

Whole bottom end,Block,pistons,rods,Gtr crank & matching Gurdle $650

3-Rb25det cranks & girdle.These were extracted from 2 good engines but didnt end up

getting used.They will need a freshen up as have some surface rust on them

$150 each

4- This set up came out of a running Rb25det

R33 Gtr injectors in Rb25det fuel rail with harness

R33 Gtr injector resistor pack

Z32 airflow meter

Dont want to seperate at this stage

Complete upgrade kit $350

5-Ross Tuffbond metal jacket harmonic balancer Rb25det.Part number 306201.

Rated to 1500hp

Has done around 1,200klms and is still like new.I paid $750 for it.

Sell $300

6-Nismo Rb25det Engine mounts (left & right). Again done around 1,200klms & comes

with the factory alloy bracks,Mounts are like new $230 pair

7-R33 Gts-t dash cluster. Showing 82,000klms $120

8-Rb25det starter motor $60

9-Rb25 valley cover $30

Rb25 rocker cover (oil cap side) powder coated blk $30

Rb25 timing cover $10

Im located on Brisbane southside.

Pick up welcome

For interstate buyers i can post or help with organising a courier for you at your

cost.

Please give me a call to make a time to view or if you have any questions.

0424-380-848

Cheers!

post-70521-0-35167800-1428901248_thumb.jpg

post-70521-0-83269300-1428901365_thumb.jpg

post-70521-0-81012600-1428901396_thumb.jpg

post-70521-0-83243500-1428901417_thumb.jpg

post-70521-0-21583400-1428901441_thumb.jpg

post-70521-0-48199500-1428901469_thumb.jpg

post-70521-0-65298900-1428901493_thumb.jpg

post-70521-0-15625400-1428901634_thumb.jpg

post-70521-0-94652400-1428901653_thumb.jpg

post-70521-0-96593800-1428901684_thumb.jpg

post-70521-0-88565400-1428901820_thumb.jpg

post-70521-0-17264300-1428901965_thumb.jpg

post-70521-0-06681800-1428902025_thumb.jpg

post-70521-0-21257200-1428902096_thumb.jpg

post-70521-0-24480200-1428902171_thumb.jpg

post-70521-0-69400700-1428902228_thumb.jpg

post-70521-0-91933500-1428902487_thumb.jpg

post-70521-0-26742100-1428902515_thumb.jpg

post-70521-0-36658900-1428902547_thumb.jpg

post-70521-0-62919100-1428902915_thumb.jpg

  • Like 1
  • 2 weeks later...
  • 3 weeks later...
  • 1 month later...
  • 5 weeks later...
  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
    • You think its the AFM? I know its a common issues on R32s. I find it coincidental how this issue raised right after cleaning the fuel system. As everything except the fuel system was fine before. I tried running it with the IACV unplugged but did not notice a difference and still stalled. However, the RPM gauge is not in the cluster right now, so I will need to connect the laptop again and use Nistune to check the RPM. I will check this weekend.
×
×
  • Create New...