Jump to content
SAU Community

Recommended Posts

Hi Guys, I have been looking for R34 GTR for long time and came across with this car on carsales.

http://www.carsales.com.au/dealer/details/Nissan-Skyline-2001/AGC-AD-16991752/?Cr=5

Can anyone please help me out with the VIN check and history of the car if someone knows. Thanks in advance.

Chassis No. - BNR34-40193

Model - GGJPRWYR34ZZAAG2BE

VIN - 6U9000BNR34401934

  • 2 weeks later...

I went to have a closer look at this car on the weekend. where do i start. in short this car's condition DOESNT reflect the km's travelled. its showing its age and is more worn. just a few things i spotted were:

- paint isnt in the best condition, looks like its spent alot of time in the aussie sun, for example the rear wing blade is faded and starting to chip

- missing front diffuser, i didnt ask if it was just removed and stored away or not, but i assume its missing

- its riding on coilovers (bilsteins) so it doesnt have its m-spec special shock absorbers anymore

- the leather interior is worn, lots of cracks and drivers seat particularly worn

- front bar left hand side looks like brake fluid may have spilt over it?? there is a stain there

- steering wheel is much more worn out in appearance for its km (my steering wheel has done nearly double the km's but much less worn in appearance

- car doesnt have factory floor mats, the floor mats appear to be one of those ebay made ones(i could be wrong here, might be nismo??)

- the car is in that yard on consignment

- as i was just tyre kicking out of curiosity i didnt open the bonnet so cant comment on engine

thats all i can think of at the moment. My honest opinion is that while not necessarily a bad car per se i wouldnt be paying anywhere near the asking price, it needs quite a bit of tlc but for the right money it could still be a worthwhile buy. Fabcar are just down the road for a third party inspection recommendation. Good luck :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
×
×
  • Create New...