Jump to content
SAU Community

Recommended Posts

Hay guys!!!
Found a great gift idea for next mothers day. Order yours now, before they sell out!!
 
 
https://www.dezeen.com/2015/04/26/21-grams-sex-toy-contains-ashes-of-dead-partner-mark-sturkenboom/
 
 
Gee dale that's a oddballer gift. How did you get on with the back?

IMG_0901.jpgIMG_0902.jpg
IMG_0914.jpgIMG_0917.jpg


Ok first mod’s done ! Black
Glossy looks awesome!
2nd mods paid -HKS stainless with titanium tip ( exhausts )

Now the 3rd pictures , ok apparently the clanking noise is I need a new front upper control Arm as picture attached - why the feck it’s so expensive !
I’ve rang Nissan’s they said it’s only few hundred dollars GS josh wants it $1700 who should I trust or know better ?

Apparently I’m not an aggressive driver ( drive like an old women) [emoji28] hence the J hook make some noises too ! I need to put my foots down once a while - where will
Be safe for
Me to do this ?

18 minutes ago, ElleAli76 said:

IMG_0901.jpgIMG_0902.jpg
IMG_0914.jpgIMG_0917.jpg


Ok first mod’s done ! Black
Glossy looks awesome!
2nd mods paid -HKS stainless with titanium tip ( exhausts )

Now the 3rd pictures , ok apparently the clanking noise is I need a new front upper control Arm as picture attached - why the feck it’s so expensive !
I’ve rang Nissan’s they said it’s only few hundred dollars GS josh wants it $1700 who should I trust or know better ?

Apparently I’m not an aggressive driver ( drive like an old women) emoji28.png hence the J hook make some noises too ! I need to put my foots down once a while - where will
Be safe for
Me to do this ?

Are they uprated ones for 1700? Otherwise ud be better off going nissan lol

  • Like 1
Are they uprated ones for 1700? Otherwise ud be better off going nissan lol



I’ll find out more tomorrow, not sure if Nissan’s knows what I’m talking about , I have the picture so I’ll bring it tomorrow with me
  • Like 1
16 minutes ago, ElleAli76 said:

 

 


I’ll find out more tomorrow, not sure if Nissan’s knows what I’m talking about , I have the picture so I’ll bring it tomorrow with me

 

 

Cars looking gd tho!!! Thats all that matters!

  • Like 1


Talk to Hanky



I did and tried to call him , must be dating.

All I need is the bush brush but sadly it’s not separate item
, come with the arm. Not in rush , I prob can pick up straight from Japan. And I have a friend who works in nissan Wangara who can install it for me
  • Like 1



I did and tried to call him , must be dating.

All I need is the bush brush but sadly it’s not separate item
, come with the arm. Not in rush , I prob can pick up straight from Japan. And I have a friend who works in nissan Wangara who can install it for me
Sounds like the go to me.
What did u use for the footing?


The sand on our block is class A and the house and shed pads are built with it so I just ran a compactor over it then laid them. They are only 2 high so I’m not concerned



  • Similar Content

  • Latest Posts

    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...