Jump to content
SAU Community

Recommended Posts

Kinugawa Turbocharger 4" T67 w/ Garrett T04R wheel T3 10cm

Less then 500km was done on this turbo, in Excellent Condition as new.

Was running a Turbosmart 45mm hypergate of the turbo.

Reason for selling the turbo is that i wish to go bigger.

Bought for nearly $1000 selling for $650 including postage to any where in Australia or $620 pickup.

Location is Melbourne

For any further inquires please can contact me on 0412595898

Thank you

post-109610-0-43664100-1431945499_thumb.jpg

post-109610-0-96059300-1431945500_thumb.jpg

post-109610-0-45795200-1431945502_thumb.jpg

post-109610-0-48422000-1431945503_thumb.jpg

post-109610-0-49359800-1431945504_thumb.jpg

post-109610-0-44589500-1431945505_thumb.jpg

Edited by King of kings

To answer the messages I received, the Turbo came of my r33 rb25.

Turbo made 330kw on 18psi. Car was tuned by Trent at chequered tuning

PRICE DROP! NEED IT GONE

$600 FOR TURBO AND BRAIDED OIL LINE AND VBAND CLAMP TO ANYWHERE IN AUSTRALIA.

OR

$570 PICKUP IN MELBOURNE.

Edited by King of kings

Turbo

Dump pipe

Screamer pipe

Braided oil line

V band clamp

All for $650 pickup ready to all bolt straight on to an r33 rb25

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...