Jump to content
SAU Community

Wtb - C34 Stagea Vic

eightsixboy

By eightsixboy,
in Four Door Family & Wagoneers

 Share

Recommended Posts

Cowboy1600 Grand Master

Cowboy1600

Posted
Posted

A daily or toy?

I've been contemplating moving mine on. It's not really suitable for a daily unless you're a sadist. It is, however, the perfect base for a weekender. It does have a few issues, however. It had a tree fall on it so some dings on the roof, bonnet and front left guard. It also needs new bearings somewhere (not sure if alternator, PS pump or something else) and a couple of other little bits and pieces. Otherwise it's very solid and quite stout with 235rwkw (I have removed the front prop shaft) now and capacity in turbo, injectors etc for 300+. All it needs is a new FMIC.

I would want the upper end of your budget, however. I've pumped nearly $10k into recently (turbo, injectors, clutch, fuel pump, coilpacks, big brakes, wheels and tyres) so would want to recover this.

Sound like something you might be interested in?

Oh, it's yellow, too.

I'm not set on selling it, but it is something I'm considering. I have no need to sell, but my want for another Datto 1600 is extreme and I don't think I can convince the missus to let me own three cars and two motorbikes. Something has to go first.

stock stagea Collaborator

stock stagea

Posted
Posted (edited)

I have been thinking of selling mine but am located in Sydney. Auto s2 c34 with dayz options. Going cheap, the only thing it needs is rust in doors fixed going for $7k

Recently spent over 6k on it, replaced all four rotors and pads, front drive shafts, rebuilt auto trans, split fire coils packs, coil over suspension all round, new alpine head unit, 3 inch exhaust from turbo back and has been serviced every 5,000 km.

Edited by stock stagea
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...