Jump to content
SAU Community

Forged Rb26 500+ Rwhp

just_racing
 Share

Recommended Posts

just_racing Collaborator

just_racing

Posted
Posted

Well it’s a sad day for me but a golden opportunity for someone looking for a tough RB. I have bought another shed ornament so I’m parting out my R32.4

Fully built RB26

CP Pistons 40 thou over size

Eagle rods

8.9:1 compression

ACL Race bearings

ARP head studs

Custom sump approximately 7-8 litres with Tomei oil baffle

Moroso external oil pump

ATI harmonic balancer

Grout filled block up to the welsh plugs

Ported head. Large exhaust and a bit smaller on the inlet to keep response

1mm oversize Brian Crower valves

Supertech double springs 90 pound

Bronze valve guides

CNC multi-angle valve seats

Cams inlet 264⁰-10mm lift and exhaust 272⁰-10 lift

Adjustable cam gears. 10⁰ on the inlet gave 500rpm extra response

Non genuine Mines style cam cover baffles

Dash 12 fitting on cam covers

Cam covers, coil pack covers and plenum all painter 2 pack metallic blue

880 cc injectors

New coil pack wiring loom from Wiring Specialities.

Only ever run E85

Produced 550 rwhp but mechanically built for 800+ rwhp all day

Changed oil every 3 events maximum and it was always clean when changed. Always ran about 85⁰c.

Can have engine running and able to do compression test but the car can’t be driven

$7k ono. I’m motivated to sell but will ignore idiots!

RB25 6 Boost manifold and Garrett GT35R GCG core steel bearing cage instead of the plastic standard cage turbo with braded lines. $2k

RB26 Apexi Power FC with hand controller, two air flow meters, y pipe, 2 big pod filters and all the silicon joiners. Wiring loom to suit r32 with mil spec round connector at the firewall. $800 ono.

Or take the engine, hot side and ECU for the a drop in package that puts you in the 500+hp club for $9k!! Tuned by Brad from Turning Point Technology.

Not on SAU very much so call or text 0414 236 724

post-40739-0-47498100-1453114676_thumb.jpg

post-40739-0-84642800-1453114727_thumb.jpg

HP and Torque - Turning Point Technology.pdf

Link to comment
https://www.sau.com.au/forums/topic/462346-forged-rb26-500-rwhp/
Share on other sites
Bart Japan Collaborator

Bart Japan

Posted
Posted (edited)

Where was this engine 4 years ago after my indiscretion?

Good luck with the sale.

Sounds like a monster engine.

Cheers

Edited by Bart Japan
  • 4 weeks later...
  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      WTB R34 GTR Guard Liners

      By Kinkstaah · Posted

      Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • itsmeyo
      WTB R34 GTR Guard Liners

      By itsmeyo · Posted

      Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • The Bogan
      NC MX5

      By The Bogan · Posted

      I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • Kinkstaah
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Kinkstaah · Posted

      You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • Dose Pipe Sutututu
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Dose Pipe Sutututu · Posted

      LOL.... you are correct there.
×
×
  • Create New...