Jump to content
SAU Community

Recommended Posts

~S and R Chassis Parts~

- S13 180sx CA/SR NA front calipers, good condition, with brake lines = $40

- CA18DE/RB20DET 270cc injectors x 7 = $100

- RB25DE S1 ignitor = $50

- 4x114.3 8mm slip on spacers, pair, 8mm = $40

- RB25DE Neo Loom = $100

~R Chassis Parts~

- R32 Black Bonnet and brackets, has a cut out of the skeleton for cooler piping, been cut for GTR style fitment, couple dents but paint is decent = $70

- R33 S2 silver drivers mirror, good condition = $30

$20 per item!!

- RB factory dump pipe

- CA stock wheel, swap for SR

- R33 Fuel Pulse Damper

- SR20 EGRs

- Rear S13/180/R32 4 stud hubs (no studs)

- S14 (fits S15 but thinner) Stock Side Mount Intercooler

- S13/180/R32 Factory Rear Camber arms

- S13/180sx brake booster (fits all S and R chassis)

- S14/S15 handbrake cables

- S13 drivers door, black, no glass or handle, small dent and scuffing

- RB25 stock cam gears and exhaust cam

- S13/180sx front air con condenser rad

- S13/180 interior snorkels and piping set

post-76822-0-69791600-1456037952_thumb.jpg

post-76822-0-10687100-1456038024_thumb.jpg

post-76822-0-18701100-1456038089_thumb.jpg

post-76822-0-58841000-1456038153_thumb.jpg

post-76822-0-03203500-1456038288_thumb.jpg

post-76822-0-48646900-1456038356_thumb.jpg

post-76822-0-54415400-1456038492_thumb.jpg

post-76822-0-97317200-1456038632_thumb.jpg

  • 2 weeks later...

~R Chassis Parts~

- R32 Black Bonnet and brackets, has a cut out of the skeleton for cooler piping, been cut for GTR style fitment, couple dents but paint is decent = $70

Photos man?

Keen if clean ~

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
×
×
  • Create New...