Jump to content
SAU Community

Recommended Posts

Hey guys sorry to make another post about a rough idle i have been using sau site for a long time now and have gone over many topics about the rough idle situation and none sounds like mine...

Anyways heres my problem

I have a r34 gtt and have had for about 2 years now.. recently i had a new fuel pump installed. 500cc injectors.. power fc z32 afm and plugs gapped to 0.8mm

And i just replaced the entire acc idle control system.. as the bolt for the idle was in shreds..

Anyways after installin mew idle/acc the car has gained alot more power.. but my issue is the car starts fine with a cold start and i have issues when its above 40c in water temp. I have to give it abit of gas to get it started.. thats my first issue

And after it starts cold or hot i get a rough idle it jumps between 700rpm to 1300rpm on idle and when slightly acclerating it just jumps like when i go to 3000 rpm it will jump between 2300rpm and 3000rpm but after a little while sorts itself out.. another thing i noticed was when i put the aircon on the car seems to idle fine.. same as when i turn the lights on?? Sounds weird i know...

But if the car is hot and say i turn the lights off or the aircon the car will go to a low idle and start to stall.

Aorry if this issue as been resolved before but i cannot find it in search..

Also i did have a high idle about 1600rpm before all the work above was done. And seemed to run fine and atart at any temp.

Any help is greatly appreciated

Thanks guys!

Link to comment
https://www.sau.com.au/forums/topic/465562-roughjumpy-idle-issue/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
×
×
  • Create New...