Jump to content
SAU Community

Recommended Posts

Electric fan question

Hey guys have a question that's been covered before but I haven't had any luck when searching for the exact answer to my question.

 

Currently have a 14" puller wired to a switch I have to manually turn on and off on my radiator (was on the car when I got it).  I want to switch to a dual fan setup and run it off a temp switch.  My question is if I use a controller like the spal where can I pull signal from without having to chop the upper rad hose and using an adapter?

 

Is there a plug I can tie into for the command for the viscous fan to engage to use as a trigger wire for a relay to kick my electric fans on?

 

Link to comment
https://www.sau.com.au/forums/topic/468315-electric-fan-question/
Share on other sites

There is no plug for the viscous fan. It's viscous, not electrically operated. You will need to install a thermostatic switch to turn the fans on and off. You can buy just a switch that has set on/off values instead of using a controller. The switch can be placed in the radiator or tapped into the housing for the top hose. Easiest way though is the adapter spliced into the top hose.

  • Like 1

Nlsmo6 thanks for the reply. Theoretically couldn't I pull the bleeder screw on the top of the intake manifold and put the switch there? Not too keen on putting an adapter in the upper hose as I think it will look tacky

You could if you retapped the hole. Smallest temp switch thread size you'd easily find would prob be 1/8 npt. Should still work fine from there and probably be more accurate as it's mounted on the engine itself. But bleeding might be a bit annoying pulling out the temp switch but pretty much the same I guess. Could even be a bit easier to bleed actually, cause the hole is bigger.

I was thinking rather than use the bleeder if I could either tap this elbow or weld a bung on and put a thermostatic switch on the end of it. Thoughts anyone?

20170101_132839.jpg

Edited by Ed.williams5

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...