Jump to content
SAU Community

Recommended Posts

  • Replies 69
  • Created
  • Last Reply

Top Posters In This Topic

I always find it incredible how factory and aftermarket installed splits have the tweeters near the a-pillars. From a sound engineering point of view, this is far from optimum. Simple physics tells you you should have the tweeters as close to the matched midrange speakers as possible. That is why I installed mine in the doors...

  • 2 months later...

Its quite simple, but i have no issues pulling stuff apart.

1. Remove ashtray

2. Remove surround around gear stick

3. Stick two screw drive between the dash and the top of the vents, pop them out. There are 4 clips holding it in, dont worry.

4. Pop of stereo surround

5. Undo the screws at the bottom and at the top

*from memory now*

6. pull out the whole unit, all three things are stuck together

7. undo the screws on the side

8. you will need to pull pretty damn hard to get the thing out, so best to flex the metal case in some way

9. it comes out.

10. do what you want. Reverse for install.

**there may be some things i forgot, but if it looks like it should come out, it probably should come out.**

Its quite simple, but i have no issues pulling stuff apart.

1. Remove ashtray

2. Remove surround around gear stick

3. Stick two screw drive between the dash and the top of the vents, pop them out. There are 4 clips holding it in, dont worry.

4. Pop of stereo surround

5. Undo the screws at the bottom and at the top

*from memory now*

6. pull out the whole unit, all three things are stuck together

7. undo the screws on the side

8. you will need to pull pretty damn hard to get the thing out, so best to flex the metal case in some way

9. it comes out.

10. do what you want. Reverse for install.

**there may be some things i forgot, but if it looks like it should come out, it probably should come out.**

Re #3, I found that it is easier if you remove the switch on the RHS of the vent. You can then poke your finger around the back of the vent and push it out easier without screwdriver marks.

:D cheers :(

Edited by Sydneykid
Re #3, I found that it is easier if you remove the switch on the RHS of the vent.  You can then poke your finger around the back of the vent and push it out easier without screwdriver marks.

:D cheers  :(

My vent surround has most of the clips broken since i got it, so it comes out quite easily, makes getting the vents out a breeze.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...