Jump to content
SAU Community

Recommended Posts

Track Fee: $150 Paying Members ($180 Non-Members)

Limited to ONLY 20 PLACES.

Initial Drift Australia will be holding it's first official skid pan training day. This unique event offers an unintimidating and beginner friendly environment for drivers new to the sport of drift to learn how to do so in a safe and controlled manner.

We will be limiting places to 20 people only and due to the added cost of the hire of the skid pan this explains the cost.

Make no mistake it will be a training day with instructors taking you through the basics and moving onto more advance skills later in the day.

Held over a full day on the Eastern Creek Skid Pan facilities, drivers will will be challenged with obstacles and objectives that will allow the first time drifter to become competent in the art of drift as well as allow more advanced drivers to refine the more technical aspects of their technique. The wet low friction surface also makes this extremely car friendly with much less stress placed on the vehicle than an equivilant competition surface.

Notes

Though not an enforced requirement of attending the day, it is recommended that you use a vehicle that meets the following specifications to benefit from the available support and tuition.

- Rear Wheel Drive

- Manual Transmission

- Functioning Limited Slip Differential

A CAMS license is also required for this event and will be available on the day for a small/nominal fee ($20).

This day is aimed at the people wanting to learn how to drift and for the other people wishing to hone there skills on the skid pan.

Places are limited and have been filling up quickly so please pre-pay to confirm your place on the day.



  • Similar Content

  • Latest Posts

    • Have a look at that (shitty) pic I posted. You can see AN -4 braided line coming to a -4 to 1/8 BSPT adapter, into a 1/8 BSPT T piece. The Haltech pressure sender is screwed into the long arm of the sender and factory sender (pre your pic) into the T side. You can also see the cable tie holding the whole contraption in place. Is it better than mounting the sender direct to your engine fitting......yes because it removes that vibration as the engine revs out 50 times every lap and that factory sender is pretty big. Is it necessary for you......well I've got no idea, I just don't like something important failing twice so over-engineer it to the moon!
    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
×
×
  • Create New...