Jump to content
SAU Community

Recommended Posts

Any help appreciated!

I have an R34 Sedan, currently seeking any information regarding the resistor/Ohms required to disable the seat belt light. I have already installed an airbag resistor however due to having new seat belts I need to get rid of the seat belt light (On dash) for compliance. 

Unfortunately  i do not have my old seat belts to plug in and test the Ohms for purchase the correct resistor. 

Have searched before posting. Thank you! 

Link to comment
https://www.sau.com.au/forums/topic/475699-r34-seat-belt-resistor/
Share on other sites

Air bag should not go off at zero speed.  Also, anyone who designs a safety system such that an explosive part of that system will go off when a peripheral sensor is not functioning properly needs to be kicked in the nuts.

Right now, you have no resistor = open circuit = light on.  Wire in 10k pot set to 10k ohms - should be much higher than the threshold value I would expect to "close" the circuit.  But if you're paranoid, you could go all the way to 20 or 50k as a starting point.  Work your way down until the light goes out.  If it turns out to be less than 1k, then probably better to experiment with a 1k pot, just to get a better guesstimate of the resistance required. 10k pots are a bit coarse.  Oh, and use linear pots too, not logarithmic.

I would expect the target resistance to be a nice number like 500 ohms, or 2k or 5k.  We use 2k & 5k a lot in industrial sensor loops to represent a working loop.

Now that I see the wiring diagram, you do not want to just hook up the resistor across those two pins.  If you look very carefully at the circuit in the box on the left, you will see that it is a voltage divider of some description.  12V comes in the top, earths are at the bottom.  Now there is more than one thing going on in there, and I am not sure if everything is to do with the seat belt switch, but let's just look at the switch for the moment.

What I don't know (because I've never cared) is whether that switch is open or closed when the belt is not clipped in.  I'll take a punt that pin 16 on the SRS module has high impedance, so when the switch is closed, current will flow through the seat belt warning lamp, through the switch and out to earth, giving a warning lamp, indicating that the seat belt is not clipped in - and pin 15 sees a low voltage.  If you clip the seat belt in, the switch will open, no real current will flow, and the 12V will turn up at pin 16.  The seat belt warning lamp is a globe, so it will have some resistance, so it will contribute to a small voltage drop from 12V....but how much depends on the impedance of pin 16 and the globe itself.  You'd have to measure these to be sure, but it's quite likely that it is almost all the 12V turning up on pin 16.

Pin 15 is a different story.  The SRS warning lamp is an LED, so it does not have the same V=IR behaviour as a globe.  It will have some fixed forward voltage drop, and I don't know how much.  I also do not understand the drawing of the wire that looks like a sense line reporting from the earth side of the LED that goes back around into the side of the LED, appears to go out the other side and go back to the wire that runs to pin 15 on the SRS module.  Ignoring all that, the 12V comes in the top and through the resistor then goes over to pin 15.  If the seat belt is not clipped in (using the assumption I worked through in the above paragraph) then the switch will be closed and current will flow down through the seat belt lamp as before.....but there should still be 12V at the top of that circuit, so I can't see how the seat belt switch would affect the SRS warning LED or what turns up on pin 15.  I can't see how the switch being open or closed will affect the voltages and currents around the resister and the SRS LED in that voltage divider circuit.

In short, I do not understand the circuit enough to advise you.  You should have perhaps lead with the diagram, because I just assumed you knew that you simply needed to put a resistor across the wiring - but that's not clear from the diagram at all.  It is quite likely that the SRS module is able to compare the voltages that turn up at pins 15 & 16 and make decisions based on that, but that's just a guess.  Maybe someone who is actually more familiar with that type of circuit will wade in.

Would I be best to measure the resistance of a R34 Skyline with factory seat-belts to find the correct one I need without playing around? The Airbag warning light is not lit. Just the seat belt dash light. I just need it gone -.- So what your saying is that it is linked to the SRS system and that is why I now shouldn't put a potentiometer in?> Uggh haha.

8 minutes ago, SammyP-R34 said:

Would I be best to measure the resistance of a R34 Skyline with factory seat-belts to find the correct one I need without playing around?

Probably not.  If you read through what I posted above, it should be clear that I do not think that there is a "resistance" that you could measure that would tell you what you need to wire in, because I don't think that wiring in a resistor will remove the seatbelt light.

What I actually think happens is that the seatbelt switch effectively removes 12V from Pin 16.  The way to mimic that would be to simply put 12V onto Pin 16.  But I must stress - I would not trust my say so!!!!!  That is all predicated on me understanding how that seatbelt switch works to make the light come on, and what must therefor happen on the line to Pin 16.  I could be wrong.

14 minutes ago, SammyP-R34 said:

The Airbag warning light is not lit.

That kind of lines up with what I was thinking would happen.  The seatbelt switch does not appear to be able to affect that light.  Not helpful though.

15 minutes ago, SammyP-R34 said:

So what your saying is that it is linked to the SRS system and that is why I now shouldn't put a potentiometer in?

Yes, that's what I'm saying, unless you know for a fact that that is how other people have solved this problem.  In which case they know something that I don't, because I can't see how it would work.

And keep in mind, that my recommendation for a pot was only for working out what resistance you need.  Not for permanent install.  replace pot with fixed resistor for maximum happiness in these situations.  (Stops it getting accidentally maladjusted 3 years later and causing problems).

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
×
×
  • Create New...