Jump to content
SAU Community

advice anyone?

Timd

By Timd,
in Engines & Forced Induction

 Share

Recommended Posts

Timd Community Regular

Timd

Posted
Posted

Would much appreciate any input here

heres my problem

In 5th the zed is maxing out at about 110km/h.

The turbo is making boost fine, havnt got my tacho hooked up but its making revs.

There is no audible pinging but I can only guess that its a problem with fuelling. Far as i can tell the rail is getting fuel, pump is priming ok. This leaves injectors. Is there anyway i can test them?

Could it be timing? It doesnt feel like the usual CAS problem i sometimes have when its cold, could it CAS related tho?

cheers

its an rb20, -not clutch related either

Link to comment
https://www.sau.com.au/forums/topic/47973-advice-anyone/
Share on other sites
Timd Community Regular

Timd

Posted
  • Author
Posted

will do it in fourth as well. I dont usually give it a whole heap in the lower gears in everyday driving specially since ive been having probems so i couldnt say how it acts in that situation. Dont think i have a speed limiter on the Blitz Access ecu ive got. Is it possibly a lose ecu connection or similar?

thanks for reply

Link to comment
https://www.sau.com.au/forums/topic/47973-advice-anyone/#findComment-967985
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      M35 Brake caliper replacement

      By Duncan · Posted

      You can use your VIN to look up the factory part number somewhere like amayama, and then look to order new if necessary. https://www.amayama.com/en/genuine-catalogs/nissan Depending on price you might want to rebuild instead. @GTSBoy I had an interesting insight into US market parts when the Titan rear calipers were sticking. New calipers were dirt cheap, about 20% more than a rebuild kit....they are just considered throw away maintenance items
    • Duncan
      Most women will agree that parking is the most taxing part of driving

      By Duncan · Posted

      Funny, but really not funny. Thank god (most) f the world has moved on since then
    • Duncan
      Jacks that fit under GTR lips that can reach the subframe?

      By Duncan · Posted

      Lots of votes for driving onto a plank first; that is the quickest way I've found, 25mm is enough for my case but that will vary by car It also depends where you are going for. On the 32 I can get to the rear diff with my floor jack if I do that end first, and get it up on stands. Then I lift the front from either front tow hook as high as needed, also onto stands. Sometimes I need a small lift on the other tow hook to get it level enough If I do the front first I can't get to the rear diff because of the angle of the car Other options are getting to the front mount of the rear subframe from in front of the wheel (if only lifting one side, or just do both which is a bit of a pain compared to one lift from the diff), or also the gearbox cross member mount on the driver's side if you are  just trying to lift the driver's side. I This is the jack I use; it says 75mm clearance but of course that is only on the lower section so if you have to reach too far in like the diff you still get stuck. https://www.snapon-bluepoint.com.sg/category/Floor-Jacks/product/Floor-Jack,-2-Ton-Low-Profile
    • Duncan
      NC MX5

      By Duncan · Posted

      On the bright side, the weather will turn much nicer for working outside shortly....sounds like you might need to start on a neighbour's garden next
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Ok so i will NEED to have this sensor anyway even with Nistune (or standalone ECU) https://justjap.com/products/genuine-nissan-boost-pressure-sensor-evap-control-system-fits-nissan-r34-skyline-c34-nm35-stagea-pnt30-x-trail-rb25det-vq25det-sr20vet?currency=AUD&srsltid=AfmBOoqfxX48bW9bEwH62orcNhtBfp7ekAL0C9Ca89ySFGUiBzXfXeze Is this the correct one? And this is only thing i need? No other "things" connected to the sensor or something? I do have the wiring.
×
×
  • Create New...