Jump to content
SAU Community

Vq25det

Ruka
 Share

Recommended Posts

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted
41 minutes ago, Ruka said:

Dosen any one know how to install a boost tap on a 2003 nissan stagea vq25det single turbo 

Only done it on a C34 but the principle is the same: find the line that goes to the w/g actuator and cut it to install boost tap. If there is a stock solenoid pull the hoses off it. You just want a hose going from boost source to actuator with a boost tap installed the right way round and with a bleed going to where-ever the bleed used to go. And of course you need a boost gauge so you know what you are doing.

Link to comment
https://www.sau.com.au/forums/topic/480597-vq25det/#findComment-7932958
Share on other sites
Ben C34 Grand Master

Ben C34

Posted
Posted
17 minutes ago, Ruka said:

By any chance would you have a photo of the line this my first time installing a boost tap 

 

17 minutes ago, Ruka said:

By any chance would you have a photo of the line this my first time installing a boost tap 

Google it. This isnt rocket science and 10s of thousands of people before you have figured it out without specific photos to spoon feed you.

 

 

 

 

What boost level do you plan on winding it up to?

Link to comment
https://www.sau.com.au/forums/topic/480597-vq25det/#findComment-7933004
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • nouveau_poor
      Unknown sound similar to BOV on positive boost with partial throttle RB26

      By nouveau_poor · Posted

      Absolutely could be. I collected data logs from when the O2 sensor was still out and also after I had replaced it so will try to compare them. Pretty confident that the affect is lowered with the new sensor, will check logs at the same RPMs/conditions. 
    • Bennym35
      New guy

      By Bennym35 · Posted

      Hey guys Long time lurker, I daily a nm35 stagea 250t rs four and I've had it for almost 2 years (very reliable 👌). Issues or just looking for information ill always find myself here having a read, so thought id join.  3inch stainless intake, pod filter, AM performance turbo dump pipe, 3inch hotdog, 3 and half inch stainless to 3 and half inch AM performance blast pipes. Bc racing coilovers. 18inch rims Hdi intercooler and trans cooler soon.  Here's my car
    • Songo
      New kid on the block

      By Songo · Posted

      thanks for the advice on the box... i was thinking the 6 speed was better for cruising on the highway but on closer inspection and comparison the Rb 5 speed box was not too different...  So the choice is going to be the RB25 box... if I can save up and find one at the right price  
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks Matt, yes that's what i am aiming for. Just going to apply the right voltage and grounds to the dash connector. Hence my search for these pins... any chance you know if these pins are in the same spot as the ones on the S15 Dash connector? as mentioned above on page 8?
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Yes, unfortunately that's the one. Signal was noisy to begin with; after driving once and looking back at the logs I saw pressure constantly swinging between 0-200psi, or staying at 0 randomly for a few seconds. There's a lot of good sensors that share the same look and feel, so don't presume they're all bad. I bought mine for 20$ off Amazon and I should have read the reviews prior, as it's clear they're junk.  I purchased a lowdollerr motorsports sensor. 
×
×
  • Create New...