Jump to content
SAU Community

R34 GTT Oil Pressure??


Recommended Posts

Hi all,

Just wondering what the normal oil pressure is on a R34 Neo 6?

Some days mine is normal, then other days it drops to just under 1, and tends to jump around a bit. Is this just a faulty gauge, like the R32 & R33s are common to have? Ive heard that skyline oil pressure gauges can be faulty?

If the pressure was to drop, wouldnt the oil pressure warning light come on ?

Many Thanks.........

Link to comment
Share on other sites

Hi all,

        Just wondering what the normal oil pressure is on a R34 Neo 6?

Some days mine is normal, then other days it drops to just under 1, and tends to jump around a bit. Is this just a faulty gauge, like the R32 & R33s are common to have? Ive heard that skyline oil pressure gauges can be faulty?

If the pressure was to drop, wouldnt the oil pressure warning light come on ?

Many Thanks.........

Hi,

Mine is usually around the 4 mark or just under, sometimes drops to around 3 id say. Hmm not sure if the warning light would come on.... I guess it should if there is a prob.

Link to comment
Share on other sites

Guest RedLineGTR

friends gt-t oil pressure sits around the 3-4 mark, from what i have seen.

This also changes with the different W ratings of oils, example (r33 gtst) used 5-40w oil and oil pressure always sat on 2 (which is where is should be on a r33 gtst or even on 1.5) when i changed to a 10-60w Castrol oil the pressure sat on idle at 4. Just something to think about. BTW The friend with a gt-t uses a 10-40w oil :rofl: My 2 Cents

Link to comment
Share on other sites

Just been for a couple of long drives and the pressure gauge has been working normally.

So, im guessing that it has to be a faulty gauge, because it only drops down low every now and then. Ive read on other forums that a lot of skyline owners have a similar problem, ane they just say to ignore it. As long as your oil levels are good, you shouldnt have a problem.

Correct me if im wrong??

Cheers.........

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Took a little trip  went to nismo hoping the get my fuel tank hoses and unfortunately they told me they didn’t have stock luckily I was able to go to a Nissan parts store and they were able to order them in for me  then can home and cleaned the tank with some degreaser and fitted the new hoses before putting it back in the car 
    • 100% I’ll hack into the 33. Strap a turbo onto the RB25DE and/or put the 25 head on a 30 block. 33 passed in cos the reserve was too high. I’ll try lowballing it again and negotiate. Aim is to have it landed and on the road for under 15k, then spend the same amount on top in mods.
    • It's generally best practise to run 1x run without VCT enabled, then 1x run enabled till redline. Overlay the two torque graphs and you'll find the desired RPM to turn off VCT. Sometimes, it might be even worthwhile turning off VCT earlier control torque/cylinder pressure and using VCT purely to spool the turbo.
    • They sell them in Malaysia for about $4
    • First time I ever have issues with Amazon, but my wife often tells me to keep an eye out for fakes. It finally got me. I wrapped up the conversation with Gates. The gentlemen I was talking to seemed to hate his job but the response time on their technical support is outstanding. He stated that the hose is marked with some variation of "SAE J30R10" but that if you only purchase a 1 foot length like I did, it is possible to get a cut between markings and have a blank hose. To no ones surprise, he stated the swelling and "gummyness" isn't normal and to replace/buy from somewhere else (He mentioned NAPA). I'll toss a small end of the new one in gas for a few days before pulling the hanger out again, just to be safe.  Hose should arrive Monday. For those running multiple pump in tank hangers, you know the joys of getting them out and back in. I'm surprised I haven't destroyed my level float yet.  Lastly once I wrap all of this up, I'm planning on hitting the dyno again in 2 weeks while I'm on vacation. I realized recently that my VCT is set to turn off at 5000RPM. I'm surprised it wasn't increased while I was on the dyno last. I'm expecting I can increase it to ~6500RPM, if not more. Should hopefully get another 15-20kw out of it. I also want him to revisit my knock thresholds. I'm occasionally getting false knock around 3000rpm. 
×
×
  • Create New...