Jump to content
SAU Community

Recipe for pain

Zebbie

By Zebbie,
in General Automotive Discussion

 Share

Recommended Posts

Zebbie Rising Star

Zebbie

Posted
Posted

Take one R33 GTST (96) - Standard seats.

Mix with a good selction of hard road (200+Km of 'Rural' driving should do it)

Add one fat wallet in right hand arse pocket.

Bake well for a couple of hours.

The result :

Take a few days off work, and have a week of pain from a trapped nerve at the base of the spine.

You have been warned. :Oops:

Edit : also have a dose of the flu at the same time, so you can stand in corners, and be *Scared* to cough!!!!

--------------------------------------------------------------

A Skyline R33, 25k.

Fuel 40 AUD.

The look on your face when you wake up the next morning and can't get out of bed.... Farking priceless.

:cuss: :pissed:

Link to comment
https://www.sau.com.au/forums/topic/48246-recipe-for-pain/
Share on other sites
72GT Enthusiast

72GT

Posted
Posted

"one fat wallet in right hand arse pocket."

This line says it all! believe it or not....this is a common cause of "mystery" lower back pain. On a visit to a Chiropractor for some back crackin' I was asked did I drive with a wallet in pants pocket. Thought he was kiddin' around...nope! Your back/spine will hate you(ask Zebbie!) if you sit for any length of time with one bumcheek marginally higher than the other! no joke. :zap:

:)

P.S. Yeah...NSW roads don't help

Link to comment
https://www.sau.com.au/forums/topic/48246-recipe-for-pain/#findComment-971449
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • oHBoy.
      2001 R34DE

      By oHBoy. · Posted

      3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
    • MBS206
      boost source Size Garrett gt28 gen2

      By MBS206 · Posted

      Why are you so adamant on going M12? Why not follow Brad (GTSBoy) suggestion. You're talking moving from a 1/8" size, to a 1/2" effectively. 4 times bigger. Why skip the commonly available sizes in between? The bigger you go, the more likely you are to strip the threads out at a later date, as guaranteed, someone will put a huge spanner on the M12 and really tighten it up, and you're only in thin wall, so not a lot of threads to engage!
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Hi. Yeah thanks. Car is already at tuners and it staying there to resolve "many" issues they do not like. So it is in a good hands. Getting a good tune on that Nistune ECU too so the car would be good. Just needs a little tune up and love.
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      Probably gonna remove manifold and turbo. I’m not sure if I can get M12 x 1.5 air tight. Could use high temp Loctite 246 or something similar, but I don’t know. Maybe it’s just best to remove everything again and weld an 1/8NPT on there instead.
×
×
  • Create New...