Jump to content
SAU Community

Recommended Posts

ever since putting on my FMIC and EBC whenever i run more than stock boost when i'm excelerating my car makes a flutter sound from the turbo side of the motor, i pulled my stock bov to check it but it seems fine, the cooler pipes are tight but i have not check the turbo outlet pipe cause i'll have to pull the other pipes off to get to it.

what else could it be, the more load the car is under the worse the flutter.

Link to comment
https://www.sau.com.au/forums/topic/49551-help-fludder-sound/
Share on other sites

not sure, but lucky its just a flutter :D

when i put my fmic in it seems to have maxed my ecu. i get a flat spot between 4500-5500 now. i'm gonna have to buy a new ecu (powerfc) or get a piggyback to fix it. much more expensive than i thought it would be :*(

lindsey34 - from what you say, it sounds like this happens when you are accelerating rather than while changing gears.. is this correct?

if so, sounds like a surge issue. I'm not too sure on a resolution. first time I have heard this happen on a stock turbo.

Jaff - all you might need to do is change the spark plugs and gap the new plugs to 0.8mm. go buy some $4 each plugs (ngk copper ones) and make sure the gap is 0.8mm. that should fix your flat spot.

still doing it the more boost the worse it is.

i'm sick of driving with stock boost might call ice and see what they think.

do you think it could possibly be the wastgate causing the problem.

you know when you excelerate how the pod makes the shhhhhhhhhhhh sound well when mine is boosted it sounds like shh, shh, shh, shh, shh, shh, shh, shh ? my brothers car has exact same mods but doesn't do it.

no the gasket is fine.

and I still highly doubt it's the bov.

what boost does this start happening at?

like at stock it's fine.. does it do it at 9psi? or 10psi?

play around with your boost controller.

start at stock and then increase by 1psi untill it starts happening..

and when it does happen, what does your boost gauge do? does it keep rising steady or does it move around when you hear sh sh sh sh sh ???

you are using an after market boost gauge right? not working off the stock gtst one i hope..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...