Jump to content
SAU Community

Typhoon......Anyone here affected?


Recommended Posts

My R32 GTST is due to leave in November.

How do they store the cars when waiting for shipping.

:zap:  

Any one know???

Depends on who you're supplier is mate. Ask 'em. But in my experience they are mostly stored in the open :rant: Undercover space is at a premium...

Richard

Well now you can all buy even cheaper Skylines...everyone knows after typhoon season there are bargains to be bought.

*small print - flood damage* :D

They may or may not say though as they do a mightly good job of cleaning out the mud from the interior, now where are those photos.

THUS...be very aware of flood damage cars!

jeez... i heard over 80 people have been confirmed dead. How bad is it over there?

Bizarre. I would have thought in a country like Japan (ie. no excuses about uneducated people, poor, etc) that there wouldn't be nearly as many deaths. What are the main causes of death?

LW

Not 80 but certainly close...

67 dead, 21 missing in wake of typhoon

Friday, October 22, 2004 at 07:31 JST

TOKYO — Typhoon Tokage left at least 67 people dead, 21 missing and 351 injured as it cleared Japan on Thursday morning, and the government said the damage was the worst from a typhoon in 25 years.

The typhoon brought downpours and strong winds, destroying houses and important cultural properties, derailing a train and disrupting transportation services across the country.  

The number of casualties was the worst in 25 years, the Cabinet Office said, comparing the latest figures with the 115 people who died or went missing in an October 1979 typhoon.

According to the National Police Agency, about 70 houses nationwide have been completely destroyed or partly destroyed and more than 4,500 houses were flooded as of 7 p.m. Thursday, while there were mudslides in more than 600 locations and nine flood-control dikes have broken.

Prime Minister Junichiro Koizumi ordered an immediate dispatch of a government fact-finding team when he met Yoshitaka Murata, state minister in charge of disaster management, government officials said.

Airlines canceled a total of 119 domestic flights Thursday morning, affecting some 25,000 travelers. The flight schedule was expected to normalize beginning in the afternoon, airline officials said.

Thirty-seven people stranded on top of a tourist bus overnight on a flooded road in Maizuru, Kyoto Prefecture, were rescued by helicopters and rafts Thursday morning.

"I was able to stay calm while waiting for help but could not hold back tears when I was rescued," said a woman who was among the 37. The group had to endure about nine hours of cold weather.

Elsewhere, 167 students and teachers from the institute for sea training in Yokohama aboard the sea training ship Kaio Maru were rescued Thursday afternoon. Among the 167, 15 suffered injuries such as fractured bones in their arms and legs.

The ship was stranded in waters off Toyama port along the Sea of Japan coast after it was thrown on a breakwater by high waves.

On Thursday morning, the typhoon was downgraded to an extratropical depression after moving into the Pacific off the Kanto region of eastern Japan, the Japan Meteorological Agency said.

The typhoon, which made landfall on Shikoku Island at about 1 p.m. Wednesday, reached Japan's largest main island of Honshu later in the day, landing in Osaka Prefecture.

The 23rd typhoon of the season then moved through Honshu overnight and went offshore near Choshi, Chiba Prefecture, at around 6 a.m. Thursday.

It is the 10th typhoon to make landfall in Japan this year. The previous record was six in both 1990 and 1993.

Many areas across Japan were hit by torrential rain and strong winds from Tokage, which is the Japanese name for the constellation Lacerta, or the Lizard.

The fatalities included a man and woman who died when a mudslide swept through some houses in Miyazu, Kyoto Prefecture, on Wednesday, and a couple who went missing after a mudslide struck their house in Kagawa Prefecture on Wednesday night.

Among the missing is a police officer who was standing guard at a cave-in on a national road in Kyoto Prefecture, the police said, adding that a 61-year-old man who was missing in Hyogo Prefecture was later found to be safe.

A two-car train on the JR Iida Line was derailed in Tatsuno, Nagano Prefecture, and fell about 4 meters into a rice paddy, slightly injuring four passengers, police said.

The typhoon also caused damage to some state-designated important cultural properties, including the roof of Tamura-do hall of Kiyomizu Temple in Kyoto and the wall of Zuiryu Temple in Takaoka, Toyama Prefecture.  

Killer typhoon death toll hits 66

....Of those who died, 24 were in their 70s and 17 were in their 80s. Another 15 were in their 60s...

As you can see it's mostly the elderly who get caught in the floods, won't leave, too scared to leave and drown.

As reported certainly the worst in 25 years as this one came straight through a major cities - Osaka, Kyoto, Kochi, Tokushima etc. This years is also the most number of typhoons in one season.

This definitely pushes the death toll to well over 100++ for this season alone :D, condolences.

The record also extends to the 2nd ever hottest summer here in Japan. Here in Osaka it was very hot and humid with no rain, but the poor poeple in Tokyo had to endure 40.1 degrees heat for well over 30 days. Highest ever recorded temp in Japan since they started recorded back in 1930's is 40.3 degrees in Yamagata IIRC.

Not a very good year.

Not a good year at all, and the reality is it's probably only going to get worse...

Yeah, beware of flood damaged cars - almost bought one a few years back - was pretty much impossible to tell it had been in a flood, and the only reason I found out was because I kep pushing the seller to say why the car (Nissan Cube) was going so cheap...

Buyers beware.

Dave also unfortunate is damage to heritage listed shrines and temples. Did you see what happened to the shrine (I forget the name) facing the Torii gate on Miyajima?...and now Kiyomizu sustained some damage :/...these historical buildings have stand the wits of time and tragic to see them destroyed by natural disaster...rebuilding them will never bring back the true beauty they have held all this time.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
    • A couple of notes about the TCM. Firstly, it is integrated into the valve body. If you need to replace the TCM for any reason you are following the procedure above The seppos say these fail all the time. I haven't seen or heard of one on here or locally, but that doesn't mean it can't happen. Finally, Ecutek are now offering tuning for the 7 speed TCM. It is basically like ECU tuning in that you have to buy a license for the computer, and then known parameters can be reset. This is all very new and at the moment they are focussing on more aggressive gear holding in sports or sports+ mode, 2 gear launches for drag racing etc. It doesn't seem to affect shift speed like you can on some transmissions. Importantly for me, by having controllable shift points you can now raise the shift point as well as the ECU rev limit, together allowing it to rev a little higher when that is useful. In manual mode, my car shifts up automatically regardless of what I do which is good (because I don't have to worry about it) but bad (because I can't choose to rev a little higher when convenient).  TCMs can only be tuned from late 2016 onwards, and mine is apparently not one of those although the car build date was August 2016 (presumably a batch of ADM cars were done together, so this will probably be the situation for most ADM cars). No idea about JDM cars, and I'm looking into importing a later model valve body I can swap in. This is the top of my TCM A couple of numbers but no part number. Amayama can't find my specific car but it does say the following for Asia-RHD (interestingly, all out of stock....): So it looks like programable TCM are probably post September 2018 for "Asia RHD". When I read my part number out from Ecutek it was 31705-75X6D which did not match Amayama for my build date (Aug-2016)
×
×
  • Create New...