Jump to content
SAU Community

Recommended Posts

Hi everyone,

I have an auto tranny s2 r33. Has 3.5" cat back zorst, blitz pod filter, and boost is upped to 9psi via a turbosx boost controller. No other mods.

What benefits can i expect to get from a dyno run? What could be tuned to extract more power from this setup?

Thanks for your help =)

Link to comment
https://www.sau.com.au/forums/topic/53257-what-benefits-from-dyno/
Share on other sites

Hi everyone,

I have an auto tranny s2 r33. Has 3.5" cat back zorst, blitz pod filter, and boost is upped to 9psi via a turbosx boost controller. No other mods.  

What benefits can i expect to get from a dyno run? What could be tuned to extract more power from this setup?

Thanks for your help =)

Checking that all is well in the A/F ratio area would be my first priority. Then you could maximise the base ignition timing. That's about it.:rolleyes:

They are good for fault finding too. You might pick up an air/vacume leak while your on the dyno too.

It's a good way of checking the car under semi controlled conditions.

But if there's nothing wrong with your car, then there's not much point doing a dyno run.

J

Ok this may be a stupid question cos I don't know a lot about dyno tunning but i'll ask anyway...

When it's said you need an adjustable computer, does this include re-mapping the stock ecu? Would you need dyno tunning at the same time of the re-map?

Or do you just tell the person that is re-mapping what your mods are and that is enough?

Ok this may be a stupid question cos I don't know a lot about dyno tunning but i'll ask anyway...

When it's said you need an adjustable computer, does this include re-mapping the stock ecu? Would you need dyno tunning at the same time of the re-map?

Or do you just tell the person that is re-mapping what your mods are and that is enough?

You can buy a premapped chip, but every engine is different. So the more accurate way is to real time tune the chip on the dyno.:P

Thanks for the helpful advice =)

i think i'll wait out on the dyno run until i get some more mods :(

Tigger if you've upped your boost then dont. I also have auto tranny but more importantly i upped my boost - put it on the dyno and found out i need a new fuel pump - unfortunately the damage was already done and eventually engine went BAM.

Moral of story is its good to check air/fuel ratios etc ..... incase your fuel pump is on the way out.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...