Jump to content
SAU Community

Recommended Posts

All, A Donation

I have a slightly damaged Carbon Fibre Bonnet to Fit a 32 GTR. I didn't latch it after working in the engine bay and it blew up under boost on my old GTS-T. Fractures across the Top.

It's a T1 type like the one on Sinista. Will require fixing, But for free it should be a good buy.

PM if your intersted.

R

We will have to let sinister decide then cause your right you did get in first but thats a very nice gester if you are letting me have first pick at it, we need more of this type kindness for fellow skyliners in need!!! :) Now i just need sinisters approval and address and i will be so happy!???????

Sorry - everyone. I posted and then went out for the day. I have so many PM's including interstaters. My pref is Local so I wont drag it out any longer. Both SkyGTRline and S13drifter were within 6 minutes of each other.

I decided to hand it over to S13drifter as he is in need ATM. And also for a GTS_T you have to take an inch out of your bracket and weld it. I know this bcos I had the exact same put on my Black GTS_T. They say the T1 fits a GTS_Tbut it didn't fit mine.

I wish I had another 9 to keep everyone who responded happy.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...