Jump to content
SAU Community

Recommended Posts

Hi guys, my mate from work wants to import a 6X model VW from South Africa. The car has been in his name for about 10 years.

Does anyone have any information how hard would this be and what is needed coz of current laws or can anyone point me in the right direction where I can find this info.

Also, would he be better off fixing up & modifying the car there or bring it here first and do it up, from the compliancing & customs point of view?

From his point of view, it would be much cheaper to do it there coz of parts availability and the labour rates.

Any info would be appreciated. Thanx.

Link to comment
https://www.sau.com.au/forums/topic/56046-importing-a-60-something-model-vw/
Share on other sites

import laws to Oz are the same no matter which country they come from. Since he has owned it for 10 years, assuming he has proof of that, "Personal Import" is the go.

Basically you can import anything under personal import, including modified cars. But you have to prove 12 months ownership. And I think you still need to get an engineering approval to register it

  • 2 weeks later...

no offence, but why is he bothering unless he is attached to the car? theres alot of 60's beetle available here, and AFAIK south african Beetles were much the same as ours..

a VW a friend of ours bought from the states owed him 5k in freight after he shipped it over, could buy a nice 60's beetle for that.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • also possibly backed up to my filler and shat down it! 🤣
    • Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
    • What sold me on Trailer Park Boys is this scene: Great stuff, just stay clear from the new Netflix production.
×
×
  • Create New...