Jump to content
SAU Community

PowerFC ECUs w/ Hand Controllers (NEW & under $1000!)

lwells

By lwells,
in Group Buys

 Share

Recommended Posts

ABuSD Veteran

ABuSD

Posted
Posted

Really keen but havent got the cash.....But might hold off cos-

Nengun is actually selling them normally for: 82,500 JPY

PFC PAGE

82,500.00 JPY = 1,014.69 AUD

How much u saving fellas? bout $30?

Food 4 thought.

  • Replies 247
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

lwells Grand Master

lwells

Posted
  • Author
Posted

ABuSD: You haven't added shipping. Also, If you actually click on the Y82,500.00 PFC, its says the cost is AUD$1150. Your exchange rate is a bit optimistic too :)

Lucien.

rs73 Grand Master

rs73

Posted
Posted
rs73: When we get to 20 people,  I will send a confirmation PM out to check that everyone will be going ahead.  If we still have 20, then I will contact Brent regarding payment.  At this stage do not transfer funds to him: a) we don't know if we will make the 20, and B) Brent isn't expecting payment yet so it would get terribly confusing.

I haven't put you down for one yet.  Let me know if I should.

Lucien,

Lucien,

Put me down for R33 S1 Gts-t (RB25DET)

Well, I'm sure for PowerFC there's no difference between S1 & S2, I think it has been mentioned a few times on this forum too.

lwells Grand Master

lwells

Posted
  • Author
Posted
Dude iam very interested, have cash ready now, my bro needs one for a 180sx Blacktop 94mdl, what are payment options?

At this stage my understanding is payment will be made directly to Nengun. You can find details about their accept range of payment methods here: http://www.nengun.com/conditions.php

However, I will confirm this with Nengun shortly.

Let me know if I should add you (and your brother) to this list.

Just a reminder to people: its very important that you will actually have the funds available: if people start pulling out at the last minute it will make everything terrible messy, so please only express interest if you can afford it. :P

Lucien.

babs Explorer

babs

Posted
Posted

looks like we got the numbers boys!

lwells, also near my order, 0423736908 is my number and [email protected] is my email.. best off contacting me on my mobile as im not that often on the internet and if i am its a rush to check my emails and never check my pm's so please, if its not too much hassle, sms or call me to let me know whats happening if not, email would be preffered.. thanx in advance.. champion thinking about the group buy.. 20 ppl in 2 days.. not bad :P

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • f00stx
      Quieter performance exhausts (or muffler add-on options)

      By f00stx · Posted

      So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Duncan
      New kid on the block

      By Duncan · Posted

      Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • iain_ST44GA
      M35 VQ25DET starter motor

      By iain_ST44GA · Posted

      Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
×
×
  • Create New...