Jump to content
SAU Community

Recommended Posts

I have never seen it, BUT the S15 fronts are not a simple bolt on addition to the S13's so therefore, don't expect them to go on without modification onto cefiro or laurel.

However with the kits available for S13's i would not imagine it would be too difficult. Would look a bit screwed up in my opinion though.

Link to comment
https://www.sau.com.au/forums/topic/56130-ichigo-cefiro/#findComment-1089402
Share on other sites

haha well its got some skyline bits, and its got some s13 bits... and maybe more :) *oooh the suspense*

i wouldn't say bolted... lol you should check out some of the conversion jobs, shit like held on by an aluminium bracket that you can bend by hand n stuff. Then there's the bog jobs... thems real fun.

Link to comment
https://www.sau.com.au/forums/topic/56130-ichigo-cefiro/#findComment-1089427
Share on other sites

However with the kits available for S13's i would not imagine it would be too difficult. Would look a bit screwed up in my opinion though.

Actually the kits for the S13 and RPS13 isnt that difficult.

Ive seen the kit for it and its easy to put together... i was going to get one for my mates RPS13 for 1800 including the lights, flared guards and vertex bar.

Link to comment
https://www.sau.com.au/forums/topic/56130-ichigo-cefiro/#findComment-1089546
Share on other sites

isn't she purrrdy? we found her in the scrap parts section of yahoo auctions, checked the VIN, it was a 1989, only problem was that the engine was siezed, so we organised it to be trucked to the port and loaded. couldn't make up some ramps coz it was too low n stuff so had to send the mechanic out to mess with it.

Interior is clean as, with custom gauge install (not usual caveman style drill holes everywhere and poke shit in) in the centre console etc.

cost next to nothing cos it was a part taking car :)

Link to comment
https://www.sau.com.au/forums/topic/56130-ichigo-cefiro/#findComment-1089950
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
    • Yeah - I mean, go the other way. Smaller range. Not larger.
×
×
  • Create New...