Jump to content
SAU Community

Airbag For V35 Coupe Skyline

SKYL1NE Alan

By SKYL1NE Alan,
in Japan

 Share

Recommended Posts

SKYL1NE Alan Newbie

SKYL1NE Alan

Posted
Posted

I have an Infiniti airbag that will fit a Japanese Skyline V35 Coupe. I purchased a Skyline V35 Coupe airbag to install in my Infiniti G35 Coupe and when it arrived I realized that my car had two connections for the airbag and the Skyline only had one, so I swapped out the cover between the two. Now I have an airbag for anyone who has the Skyline V35 and want to make it like the Infiniti G35 Coupe. It will bolt directly into place and has the one connector.

My email is [email protected]

Please contact me if interested.

I posted here because there was not a classifieds section in the Japan area.

Link to comment
https://www.sau.com.au/forums/topic/56353-airbag-for-v35-coupe-skyline/
Share on other sites
Rezz Grand Master

Rezz

Posted
Posted
Now I have an airbag for anyone who has the Skyline V35 and want to make it like the Infiniti G35 Coupe.
Can I suggest you post this in a Japanese speaking BBS or forum, you might have more success there, because most non-Japanese Skyline enthusiasts wouldn't dream of swapping Skyline badges for Infiniti ones. (Japanese guys on the other hand think the Infiniti badges are different [read: Infiniti G35 isnt sold in Japan] so they must be good.)
SKYL1NE Alan Newbie

SKYL1NE Alan

Posted
  • Author
Posted

Hi Rezz,

Can you tell me some place to list this item so people in Japan will see it. It is quite specialized because the airbag now only has one connection. I had to swap the cover from the Nissan Skyline Airbag to the Infiniti Airbag. The airbags do not interchange but the covers do. Someone would actually have to purchase an Infiniti Airbag and swap the cover over to theirs.

This is ready to go onto a Japanese Skyline V35 Coupe, and will no longer work on an Infiniti G35 Coupe.

If you have any suggestions please let me know or if you would like to make $25.00 sell it for me.

Kind Regards,

SKYL1NE Alan

SKYL1NE Alan Newbie

SKYL1NE Alan

Posted
  • Author
Posted

Hi DCD and thanks,

I think this should sell very well because it is not made for a Japanese V35 Coupe. The airbag has to be taken apart and the covers interchanged.

The Japanese Coupe has one connection to the airbag, and the Infiniti coupe has two. Now this one has an Infiniti Logo and only one connection because the airbag assembly is Japanese and only the cover is Infiniti.

Kind Regards,

SKYL1NE Alan

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • albyz34gt
      34 de+t conversion using s2 stagea automatic transmission, engine harness and ecu

      By albyz34gt · Posted

      Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Duncan
      R32 GTS (RB20DE) Injectors Replacement

      By Duncan · Posted

      Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • GTSBoy
      Wheel Sizes & Offsets For Skylines

      By GTSBoy · Posted

      There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • GTSBoy
      Rear Sway Bar Busshings - Holden Astra TS (2002)

      By GTSBoy · Posted

      I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...