Jump to content
SAU Community

Recommended Posts

S15 manual injectors are a red/brown colour

the part number is 16600 91F00

Auto injectors are a purple colour and are the same as S14

http://www.nissansilvia.co.nz/tech/partnos...s.htm#injectors

after market injectors like Sard 550cc etc are the same part number for Rb25det and Sr20, so the factory S15 and Rb25 should be the same as well.

I am getting the injectors at the end of next week, so I will be able to confirm more then

The ones I am getting are second hand for $300 set of 4

Brand new ones from nissan are $257 plus gst each!!!

wow!

So the 8 you are getting are second hand?

You said a set of 6 will be $450, is this assuming i can find 4 second hand for $300 aswell?

How old are the injectors?

  • Replies 70
  • Created
  • Last Reply

Top Posters In This Topic

ive got Autronic sm2 and a 044 pump. I have 320rwhp at 1 bar so id say I would have less power than a gt30 with manifold.

But driving to work i hardly even get onto +boost to use alot of fuel!

Was there alot of fine tuning done for daily driving and not just full throttle? I think thats where mine is lacking that extra bit of fine tuning with the pfc

Thats all it would be INASNT, the lack of tuning of AFR & Ignition at part throttle.

I had a VS many moons ago that had part throttle/cruise tuned up close to 17:1. That sounds really lean but that is what I was told.

Unsure how it was done but it definately picked up fuel economy.

Obviously emmisions would have been out the window.

I have noticed the stock ECU tends to run quite lean in the lower rpm ranges (up to 3000-3500rpm) with part throttle (13-13.5:1)

Every car I've seen tuned has always lost this 13-13.5:1 AFR in the lower rpm ranges, the tuners tend to head towards mid 11's to flat 12's.

Leaning it out slightly does reduce response and power under part throttle but I guess that is the trade off.

I'll create a new thread when mine is tuned up as I'm going to have a look exactly how the AFR's & Ignition are with part throttle over the stock Powerfc Map.

mokompri.

Yer not sure on that.. regarding leaning out to increase response.

I've been told by a few tuners that the RB's like to run just that bit more fuel through the mid as it increases response and power.

Maybe this is why the Japs run so rich and use ignition timing to get the best power/response.

  • 1 year later...

Finally i found this topic in a forum

I am in the midst of putting RX7 injectors in to my RB20.

Can anyboy Pleeeeeeeeaaassse show me an easy way of modifying the plugs without demolishing them.

If i have i dont mind but if somebodys done it before and can help or show pictures ill be ecstatic

Thnks heaps

Smackey

Finally i found this topic in a forum

I am in the midst of putting RX7 injectors in to my RB20.

Can anyboy Pleeeeeeeeaaassse show me an easy way of modifying the plugs without demolishing them.

If i have i dont mind but if somebodys done it before and can help or show pictures ill be ecstatic

Thnks heaps

Smackey

I've done the RX-7 (red top) conversion and its not too hard to do.

Best bet is to buy new injector plugs (round the $35 mark new for all six). Then you

You can get the correct crimpers from dicksmith for the plug pins(round 12 bucks or so).

I acually used new wires for the new plugs and then just cut of the old plugs and soldered the new plugs onto the loom.

As for fitting the injectors into the rail. They can be squeezed into the rail with out mods but its a real squeeze . I would recomend getting the rails holders boared slighty to make it an easyer fit.

Also these injectors are a slight pain to get a stable idle at stock rpm (650rpm)

When I did this I set it to idle (on the stock ecu)to the stock GTR idle (950rpm) and it worked fine.

Hope this helps.

Finally i found this topic in a forum

I am in the midst of putting RX7 injectors in to my RB20.

Can anyboy Pleeeeeeeeaaassse show me an easy way of modifying the plugs without demolishing them.

If i have i dont mind but if somebodys done it before and can help or show pictures ill be ecstatic

Thnks heaps

Smackey

Im running rx7 ser v inj. and they didnt require any mods to the plugs as far as i know.

Im running rx7 ser v inj. and they didnt require any mods to the plugs as far as i know.

YES they do... More hereRX7 550 cc into RB20

Sorry wrong page - better now - hell thats a crap site - anyway just cut the little plastic lug inside the RX7 injector off and the standard RB20 plug will fit OK

YES they do... More hereRX7 550 cc into RB20

Sorry wrong page - better now - hell thats a crap site - anyway just cut the little plastic lug inside the RX7 injector off and the standard RB20 plug will fit OK

I was referring to the wiring plugs, but yes all u need to do is chop that little lug off (not a huge mod at all) and they drop straight in.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Photo of manifold showing gate location? I mean, it's 6Boost, so we probably shouldn't be worrying, but always wroth knowing what the layout is. Plumbed back to atmosphere? Or into the dump?
    • Yes correct. Also, I'd avoid applying it to soft paint (however I doubt you'll ever have to deal with it in practice). So any paint that hasn't fully hardened, could be a 1k paint that never fully hardened or it could be a 2k paint that was laid down thick and hasn't yet fully hardened. 
    • Bit of an update to this one. Having some issues on the dyno that held us back (boost spiking) and I want to pass some info over you guys and see what you think is wrong with my setup. The current readout on this dyno is 462rwkw on a low reading dyno so keep in mind it is a real world 500rwkw setup on a hub dyno. Don't read into the power figure too much as a sign of the issue. The short and curly of it is: 2.8 Litre Racepace build RB25 NEO N/A Head with VCT (internally standard however ) Borgwarner EFR 8474  Turbosmart 50mm Straight Gate + Mac valve 6Boost Manifold 4" dump to full 4" exhaust (nil restrictions) Wastegate plumbed back in and all angles in the exhaust system are acceptable and not too sharp. GFB SV52 BOV in cooler piping  Turbosmart BOV in EFR Housing   The issue we are having is it comes onto full boost for example at 4000rpm and spikes to 24/25psi, before dropping down to 17psi before slowly rising back up to the target boost of 23psi. It was extremely uncontrollable and the tuner actually had to ramp in boost progrssively with each 1000rpm on each boost setting we selected to try and reduce the amount of spiking. Sometimes we would see a drop of 10psi from the peak at the beginning of the run, to the low, until it took the next 500-1000rpm to stabilise back up to the target boost. The tuner is pretty confident that the straight gate is just a poorly designed product and leaks too much boost upon cracking the gate open and theres no way to fix it other than going to a poppet valve. He's also confient theres no ignition breakdown or floating valves. The fueling is extremely stable as well. Turbo speed is somewhere around the 109,000rpm area. The spanner in the works for me is that prior to this Borgwarner and StraightGate, the car was tuned on -5 twins at a diferent tuner, and he also had issues controlling the boost with it spiking around the same rpm range, so to me this sounds like the same issue and it can't be anything on the turbo side as this was all changed and I think the behaviour is extremely similar, if not the same. We also removed the mac valve and did a run on wastegate pressure and it still spiked and had the same behaviour. My thoughts on possibilities are: Boost Leak VCT Cam Gear isn't reliably activating consistently - (On this however, we did a run with the VCT disabled and the boost still spiked) Turbosmart BOV is not handling the boost? However this seems unlikely to not be able to handle 20psi. I have a couple of logs that I can't make sense of if anybody knows how to read them and can obtain further logs of other parameters if they are not enough, happy to pay for anyones time. The dyno readout with the power figure is the most recent last week. The other picture is from two weeks prior to that where we couldn't break 400kw (we removed the cat), however the issue of the boost control persisted. @Lithium @Piggaz @burn4005 @GTSBoy @discopotato03 I've tagged those that were quite active in recent pages here, no disrespect to those that know turbos well but I missed tagging. Cheers 
    • I recently purchased a 2018 Infiniti Q60, which has an SD card navigation map. I can see my system has options for real time traffic updates etc, and am wondering if there is something I can purchase to get this working? I can see there are at least updated maps for USA and Canada, but nothing for Australia. Surely Infiniti took changing road systems and city expansions into account when they decided to use an inbuilt navigation over Android Auto/Apple Car Play, or are we doomed to drive on streets that don't exist in the navigation system if you drive to a new area?
×
×
  • Create New...