Jump to content
SAU Community

Recommended Posts

Hey Guys..

As part of my upgrade plan, ive got two more steps to go...

1) Up boost to 12psi, install power fc and tune

2) install Ext Cam Gear

Now - in regards to step (2), i understand that this is a mechanical retard.

My question is (sorry if its dumb) - is there any advantage to do this together/prior to the power fc tune for maximum gains....or does it matter nothing since the retard is mechanical ??

:D

There is no difference if all you're doing is replacing your factory gear with an adjustable one ;)

I have heard plenty of people with 33 gtst's getting good results by retarding the exh gear a couple of degrees. As with any modification, you are ALWAYS better to perform the change AND THEN tune for it afterwards.

Adrian

The retarding of the cam gear will do a couple of things.

First your peak power may be a a little lower, this is why people complain about no gains they are looking at the peak power dyno reading. However the boost comes on a tad sooner and the power across the boost range bar the very top end is up usually 10hp or so.

Bottom line is you will have a quicker car at the end of the tune. The guy without the cam gear might beat you in a dyno comp but, you kick his ass everywhere else that actually matters.

As mentioned you need to retune the car and focus on the mid range power timing and fuel maps.

Hi Guys...

2rismo - what you have stated makes sense - however, i wasnt sure if there was any difference between mechanical retard and overall tuning capabilities..

rev210 - the exact reason why i got them...i really dont care about the end dyno figure, just hoping for a good torque (re: 1/4 mile) result...

So - what im hearing is that it seems better to install the cam gear before the overall tune..

Thanks for the replies guys...seems like ill have to wait a while longer before i do the power fc tune... (re: ill do the cam gear install first)

;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'll just leave this with, holy shit, those cars at work are awesome, and this will look wicked!
    • Could you modify this duct so instead it pushes the extra air through the radiator too and not down and out? For temps, I know it's not the greatest idea, but as a bit of a last resort, you could use a very intermittent misting spray onto the front of the coolers/rad. You don't want to be soaking them such that water is dripping off, but a small most on/off so that the water evaporates. That point of it constantly evaporating, rather than being soaked in water, will pull a LOT of heat out of the cooler. I'm literally thinking just the little mist sprayers for a garden from Bunnings. Being in a low humidity climate it will help even more! The other trick if you want to be ghetto is some shade cloth hung in the opening, and keep it wet. Pretty much now it's acting like an evap cooler on a house, but cooling the air you need to use to cool the radiator...   On a topic to think about too though, when air enters through the bumper, is it all nicely ducted from the edges of that opening back at a nice angle, or is it like most cars, and the edge of the opening just stops, and suddenly it's wayyy wider behind that? If it does the later, get it shrouded out at nice angles. When that opening changes too rapidly, it can actually cause a high pressure zone between the front bar and radiator, and limit air flow into that area, which means less air for cooling, as it effectively stalls the air, AND adds to drag...
    • Do you have any before and after photos? That's $200 just for the hydro blasting?
    • It doesn't look like there's a lot of options out there these days, and what's out there is performance oriented aftermarket stuff (with the GTR markup) I wonder if there are other cars with similar springs, after all its just a matter of length, diameter and stiffness. Alternatively, I did see coil spacers. Probably not the best option, but could be serviceable too.  
×
×
  • Create New...