Jump to content
SAU Community

Recommended Posts

Thought I would start a Stagea Intercooler thread, so here goes

The stock Intercooler placement is CR*P, and so relocation/replacement is

a viable option

I see lots of 600x300x76 coolers, is there enough room for one of these

or is a 2nd hand GTR cooler a better bet.

Any hints on piping etc, how easy to do

Many thanks

Link to comment
https://www.sau.com.au/forums/topic/58586-stagea-intercoolers/
Share on other sites

Enough room for a GTR cooler - fills up the front bar nicely. About 25% of it is wasted though - sits up quite high. I would recommend a second hand gtr cooler - excellent flow.

Ken

Enough room for a GTR cooler - fills up the front bar nicely. About 25% of it is wasted though - sits up quite high. I would recommend a second hand gtr cooler - excellent flow.

Ken

Cool

How difiicult to fabricate/route the piping (no cutting of panels I hope :Oops:

A hole saw is need for the box under the battery, you need a hole there to run the piping. Be prepared to find a new washer bottle too - that gets in the way. You are probably better off getting a r33 ic kit, should bolt up without a problem.

Cheers,

Ken

Depending on your power goal, Trust make an replacement intercooler that sits in the stock location.

Three times the thickness, MUCH better end tank design, and it flows heaps better too.

I'm not sure how much power it will support, but if your after a mild setup it might be worth looking at (secondhand). You may be able to pick one up for the cost of just the pipework on a FMIC.

J

Depending on your power goal, Trust make an replacement intercooler that sits in the stock location.

 

 Three times the thickness, MUCH better end tank design, and it flows heaps better too.

 

I'm not sure how much power it will support, but if your after a mild setup it might be worth looking at (secondhand). You may be able to pick one up for the cost of just the pipework on a FMIC.

 

 J

Now THAT sounds like a plan. I'm interested in anyone that has a lead on one of these units.

Based on the Trust website, there is no specific Stagea cooler, but there are genuine replacements for the R33 & 34. I was under the impression that the C34 intercooler mounting is the same as R34. Can anyone clarify that?

I can clarify that the R33 GTS-t Trust side mount intercooler is a near perfect fit on a 96/97 Stagea cause that's what's on mine at the moment.

The top and back mounting points line up perfectly, although the front mounting point doesn't cause the Stagea's tow hooks are located further rearward compared the the R33's. Although the two mounting points (the top one in particular) makes it very secure. Remember that the two hoses help hold the cooler there too.

The only other thing I had to do was trim about one inch of plastic off the inside of the front bar. Mind you, when you put the black plastic wheel arch thing in you can't even see where I trimmed the plastic !!

I noticed a noticable difference in responce and power when I put it in. I wouldn't say it gave me a million kw at the wheels, but there was a definate difference.

J

I can clarify that the R33 GTS-t Trust side mount intercooler is a near perfect fit on a 96/97 Stagea cause that's what's on mine at the moment.

The top and back mounting points line up perfectly, although the front mounting point doesn't cause the Stagea's tow hooks are located further rearward compared the the R33's.  Although the two mounting points (the top one in particular) makes it very secure.  Remember that the two hoses help hold the cooler there too.

The only other thing I had to do was trim about one inch of plastic off the inside of the front bar.  Mind you, when you put the black plastic wheel arch thing in you can't even see where I trimmed the plastic !!

I noticed a noticable difference in responce and power when I put it in.  I wouldn't say it gave me a million kw at the wheels, but there was a definate difference.

J

Hi J, was the standard Stagea intercooler the same as a R33GTST or R34GTT?;)

Mercury Motorsport just fitted a FMIC to the stagea. Fits behind the grill without any choping into it. The only thing they had to do was take a little slice out of the re-enforcing bar. They did a damn good job.

Cheers

Gary

The 'cheap' upgrade I read about was to fit the 25GTT cooler as it was a better design than the GTS25T unit. FYI, the Trust webby with all the models available is: http://babelfish.altavista.com/babelfish/t...cooler_kit.html

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
    • Just like in being 14mm too small (296mm) makes it not fit, being 14mm too big (324mm) it also won't fit. You want to find the correct rotor.
    • @GTSBoy Ok so that was the shops problem...they showed R33 rotors on R34 page and i did not know 296 do not fit(and are for R33) Yes i bought "kit" with rotors and pads. Pads are ok(i have GTT calipers front and rear). They have some 324mm but no 310mm. So i dont know if they would fit. I have 17inch LMGT4s So another question. Can i fit those in the rear or they are just "too" big for that?
    • I started removing the tank a while back with the intent to give it a proper clean. Got to a bolt that I couldn't undo completely due to a diff being in the way, so just said f**k it and siphoned the gluggy old fuel out and called it a day. Looking it the tank it looks less corroded than the one in the pics for that billet hanger from Frenchy's anyway. Isn't it the fuel filters job to worry about this stuff? I scraped off most the crusty shit of the hanger but will give it another go before reinstall coz maybe the fuel and return pipes are also full of gunk  
    • Pretty sure it is a common fault. I believe this is the only part you need, but don't quote me as I don't have a V36.  I also believe it is a bit of a pain to change and the device needs to be encoded to the car once it is replaced, so may need someone with the right tools. Buy Genuine Nissan 48700JF00D (48700-JF00D) Lock Set-Steering. Prices, fast shipping, photos, weight - Amayama
×
×
  • Create New...