Jump to content
SAU Community

Thursday 23/12/04 - Christmas Lights Tour


Recommended Posts

If any of you are interested, I will be leading some people through the local southside christmas lights on Thursday night. I'm going on the BCC bus tour tonight and I thought I might just follow that route on thursday night. It's meant to go past most of the award winners on the southside of Brisbane.

If any of you are interested, we'll meet at Crazy Clarks Springwood carpark around 7:00ish. I'll make it earlier so you guys can bring the kids if you wanted to.

If not ones interested in seeing the christmas lights, tell me so and I'll scrap the idea :P

  • Replies 59
  • Created
  • Last Reply

Top Posters In This Topic

I guess I better take a pen and paper tonight to write down the streets then hey!

Just grab the Bus Drivers map Erin :P

But I should be there! I havent gone looking at chrissy lights for years!

This isn't going to be some full blown christmas lights spectacular, but I'll try my best to follow the same route that the lost bus driver took tonight. Obviously without the wrong turns. But that's half the fun. It went through runcorn, kuraby, algester, parkinson, crestmean, ... more crestmead, then to springwood.

never been to one of these meets before i might come.. if you see a red 34 crusin around its me tryin to find crazy clarks lol.. i think i might no where it is.. its on the left heading towards the coast at a large shopping center is that right?

If you are heading south along the freeway you take the rochedale/springwood exit and go straight through the set of lights at the top. Continue along that same road through another set of lights and it's on the left before the right hand turn off to go to the gold coast.

Seeming it's also late night shopping and 2 nights before christmas, there might be a few parking issues, but most of you know my car, so if you see me... just park and come over.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • It's been quite the ordeal but hey, at least you figured it out.
    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
×
×
  • Create New...