Jump to content
SAU Community

Recommended Posts

Hi, I am thinking of purchasing my mate's r32 gtst, and it has the old scholl air con unit, not the newer climate control. What I want to know is, is it possible to install the newer r32 climate control module, as I have gotten used to it in my r33? Has anyone done this before. I know it is pretty pendantic, I just like the control that climate control allows for.

Link to comment
https://www.sau.com.au/forums/topic/60250-r32-climate-control-installation/
Share on other sites

Pedantic???? That's one word for it. Luckily, it is probably not practical to convert. Prob some wires missing from loom, etc.,. If you ever get some of the weird problems that the Climate Control can throw at you,just in order to not have to turn something up, down or off, you'll wonder why you wanted it.

yeah.. it might be a "non mspec" thing.. or just a factory option that is 95% optioned on...

I got the old sliders too.. I know they work, but hell, I like the digital thingo, makes you feel like you have a fancier car (pedantic I know).

I picked up the control unit and the loom for $100 to do the conversion.. I have had a quick look, and it looks like the slider controls actually have the old-style cable mechanism which opens up the various flaps near the firewall. This makes it tricky, as I think the newer method works with actuators (like the R33) to open the vents, etc. So I'll probably need the actuators to actually do it. Looking more and more expensive.

I can't find out too much information either on the conversion, other than for the S13, which I assume it could be similar to.

I really have to pull the whole dash apart to find out what sort of task it is.. not high on my list of priorities right now.

Hmmm... well guess i'm just thankful i have the Climate Control, however, if they were an option i can't see it being a massive task to fit on after the fact. After all the factory had to do it and it'd be woefully ineffiecent too make really to do (altho if it's ALL behind the dash that's much easier with a partially assembled car).

Good luck.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...