Jump to content
SAU Community

Recommended Posts

I had the say problem after my rebuild. cleaned of all carbon build up and idle was going up to 1500-1600 rpm. I could not find any air leaks and the hoses were all correct. At the back of the intake houseing there are the air by pass hoses that feed the aac and the cold start valve with air to bypass the trottles, blocked of these hoses to make sure that the vave were not stuck open (the rpm should drop). The only way i got the rpm down was to readjust the main throttle stops them selfs and then the tps switch. It is now at 950.

The guy working on my car said he got the idle down to 950 when the oil is cold but after its warmed up its up around 1000 then if you boost it it gets upto 1100. I dunno he said it could be the oil??? Im using motul 4100 turbo light

My R32 GTR is idling high too but thats after i took the whole intake collector off..a way to see if you have leaks is by spraying aero start. It will make the revs pick up when and if there is a leak around your mannifold etc..Mine hasen't shown any sign of that when i tried it but it can get as high as 1900rpm after driving...i took off my AAC valve and cleaned it out i will get a new gasket for it but i dont think thats the problem..Also since this happened i lost all boost..I thought a vacuum line could be the problem..seems more like the wastegates arent closing to build boost than a turbo failure...So i need help with this too..how can i test the stock boost control solinoid...?? Any ideas? i have a completley stock GTR. Thanks

You need what is called a mightyvac.

You can apply vacuum or pressure to the actuator and test what pressure it takes to activate the arm.

all of you sound like you are having the same problem.

The throttle body should not contain any carbon build up. It should be clean at all times or whenever possible. Any crap stuck in there will cause air to be able to pass and will effect the idle.

However, when you clean your T/body, it is very important not to just spray throttle body clean or carby clean straight into the throttle body. Doing this will stuff the TPS.

You need to spray onto a rag and use the rag to clean the butterflies.

On the high idle side of things. The TPS should not have to be adjusted!

Do not move it unless you have the correct testing equipment to set it properly.

To just turn it in the hope of good results is wrong.

If you have the test specs from the manual then use them to check voltage and such. This will tell you if the TPS is stuck on wide open throttle, which it probably is.

No matter what you do to the AAC valve, it won't bring it to correct idle.

All of the above posts are good for maintenance anyway so do them also.

If the TPS tests bad, throw it away and get another. Simple.

Have you tried cleaning your AFM? Sometimes this can also effect your idle.

If you don't have the testing specs, PM me and I'll give em to ya.

Hope this helps.

The other thing is.....

About the boost guage reading. Your guage should read between roughly 15hg-20hg Which is -0.5 - -0.7bar

Any lower than 15hg and you have a vacuum leak somewhere. Or your manifold is not getting enough. I would explain but it is irrelevant.

  • 2 weeks later...

To add a little more to this, the TPS voltage should be approx 0.5volts with the throttle closed. Moving it just a millimeter will change this value by quite a bit so test it, move it, test it, move it. Check base timing since advance equals faster idle. As said before, clean the AAC out. If all these things checkout and the idle is still high, simply adjust the idle speed and back it down a bit. Unplug the AAC and turn the screw on the side clockwise.

My 2c

-Matt

I've had this fixed for a while now

One of the hoses leading to the air reg had a small split

Very simple but time consuming fix as I hadn't been able to find it till I pulled the manifold off.Gave me a good chance to inspect everything and there was bugger all carbon buildup on anthing which was good.

The TPS on a GTR is mounted on the manifold not on the throttle bodies so theres no chance of spraying it when cleaning.

Thanks for all the advice, really happy its fixed.

  • 1 year later...

i have an r33 and im getting weird idle probs also, the car was sometimes stalling becuase of extremely low revs but since yesterday it is idleing at around 1300 - 1400 rpm, with the occasional rpm spike, but will never drop below 1300rpm

im taking it to the local performance shop for a checkup, ill let you know what they find.

cheers

(if anyone has any ideas, let me know)!

:geek:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • I forgot about my shiny new plates!
    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
×
×
  • Create New...