Jump to content
SAU Community

Recommended Posts

im starting to get a feeling that it could be a temprature problem (with mine).

i changed the coolent and it seems to have made a difference. before the problem would happen after a while and then keep happening untill i left it and came back to it the next day. now when it happens i can turn the car off for 2min and it is fine again for a while (it also doesnt completly stop, it will still idle... kinda). im thinking that the factory gauge is bogus (reads at about 2/3) and that my increased boost (13psi) with no extra fuel is causing leanage thus slight over heating and bad fuel vapourisation (when boost comes on it stalls badly). i also want to take a look at my thermostat.

question... what is the round metal tube that is half way along the top radiator hose and i take it that the thermostat is in the housing that joins from the bottem radiator hose??

also what is the recomended operating temprature range for the rb20det?? (i may perchase a temp gauge if i have some spare money).

cheers daniel

im starting to get a feeling that it could be a temprature problem (with mine).

i changed the coolent and it seems to have made a difference. before the problem would happen after a while and then keep happening untill i left it and came back to it the next day. now when it happens i can turn the car off for 2min and it is fine again for a while (it also doesnt completly stop, it will still idle... kinda). im thinking that the factory gauge is bogus (reads at about 2/3) and that my increased boost (13psi) with no extra fuel is causing leanage thus slight over heating and bad fuel vapourisation (when boost comes on it stalls badly). i also want to take a look at my thermostat.

question... what is the round metal tube that is half way along the top radiator hose and i take it that the thermostat is in the housing that joins from the bottem radiator hose??

also what is the recomended operating temprature range for the rb20det?? (i may perchase a temp gauge if i have some spare money).

cheers daniel

Sorry I thought you were talking about the blowby control valve when you were talking about the air regulator right under the T/body.

The thermostat should operate around 76.5 degrees.

That round metal tube is just a junction, possibly to shorten the top hose or provide support for it. Not exactly sure what it's purpose is.

Also when you say the fuel pressure is good so the pump is fine....this is not always correct. You can still have full pressure but no flow.

A flow test will reveal any problems with the pump.

It should flow at least 2 ltrs per minute I think. This is when connected directly to 12v

Check other sensors like coolant temp sensor.

Try driving around with a fuel pressure guage connected. See what pressure it runs when it actually dies.

With this kind of problem you will need to test everything when it is ok then retest everything when it dies, either during or after it dies. I wish I could go out there and test it for you but I'm in Brissy so unfortunately that's outta the question.

The problem was the airmass meter.

We finally got it to play up while the car was hooked up to to a diagnostic scope that logged

pulse width, airmass meter output, ignition, A/F ratio etc. When it started to play up the Airmass meter output dropped out.

We cut the sealant and removed the cover. The connection to one of the pins had broken.

A dob of solder and siliconed the cover back on and she's fixed.

Awesome. Good to hear it all worked out for you.

I'm having problems with my AFM again. It's the second one. I'm thinking about either upgrading it or spending the extra couple of hundred and installing a Microtec so I don't need one anymore.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...