Jump to content
SAU Community

Recommended Posts

Hi all fellow Liners!

I just need some advise on mods for my Skyline.

I've had a guy give me a quote on a few things. Guy from Ovaboost Performance in Malaga.

Basically want to do some minor type stuff, know absolutely sweet f all about these things and really want to learn as much as I can.

What I got quoted on was:

Intercooler,

3" Dump pipe (cause it's stock from the cat back)

Manual Boost controller &

SAFC.

This according to him would get me about 250rwhp. Think it involved turning up the boost of the turbo alittle. The approximate cost was $2500, which includes fitting and tuning.

At this stage I don't want to go overboard, but maybe down the track I will change the turbo as well.

Just want to know what you guys think, recommend etc? Also I've been told it's better to have and Auto boost controller.

Cheers,

Pulp.

Link to comment
https://www.sau.com.au/forums/topic/62496-advise-on-mods/
Share on other sites

I'm currently hitting 228hp with a front/dump turbo back exhaust and an air filter. boost is standard.

front mount/safc/tune should give me more than an extra 20HP, so you'd hopefully hit 270hp. although some people have said new injectors might be needed after 270hp.

good luck.

Link to comment
https://www.sau.com.au/forums/topic/62496-advise-on-mods/#findComment-1177715
Share on other sites

where do i get an intercooler pipped and fitted for $1000 ?

i would forget the safc and put the money into a better electronic boost controller because you only have limited boost to work with on the stock turbo and you dont want to waste 2 psi as a spiking buffer .

Or just forget about boost control , youll probably hit about 10psi with a 3inch exhaust anyway and then put the money towards a powerfc which is a full replacement computer and much more programable than the safc.

Link to comment
https://www.sau.com.au/forums/topic/62496-advise-on-mods/#findComment-1178266
Share on other sites

Thanks guys!

Damn I thought that my quote was sounding good!

I hope I'm not getting ripped!I'll do some shopping for sure.

arkon, you were saying about not using the SAFC, does the electronic controller adjust to our fuel type etc too? Cause the guy was telling me that the SAFC did this. I don't know if I really want to go too much into upgrading the computer (PowerFC), just gonna do a little at this stage.

Sorry still learning all these things!

Link to comment
https://www.sau.com.au/forums/topic/62496-advise-on-mods/#findComment-1179030
Share on other sites

adjusting to our fuel type is not really required the stock ecu will do just fine on 98 octane fuel at the tune level you are looking at .

an electronic boost controller will do the same thing as the manual boost controller , ie control boost . however it does it with more accuracy and is controllable for hi and lo settings things like that .

the problem with the safc without going into to much technical stuff is it doesnt do that much so you wont find a huge gain with it now , maybe 15-20kw and later on it wont offer the level of tuning required to support more serious mods . so for the level your at the stock ecu will be fine

Link to comment
https://www.sau.com.au/forums/topic/62496-advise-on-mods/#findComment-1179277
Share on other sites

I see, now things starting to make sense!

I was told by someone the same thing about the controlling of the boost, but wasn't sure if it would be necessary. I think I'll go back and get him to give me another quote with the electronic controller. I don't want to have to go back and make changes later cause I wont be happy.

Thanks again Arkon! Great help.

Link to comment
https://www.sau.com.au/forums/topic/62496-advise-on-mods/#findComment-1179288
Share on other sites

Hi pulp,

Do you want to go faster or just have a 250rwhp dyno to brag about?

If the answer is faster;

* S-afc II is a good move. Buy one second hand for around $400 + $100 to tune.You can turb around and get most of your money back if and when you need a PFC.

* Manual bleeder boost controller. Nothing wrong with them for a factory turbo. Don't waste money on an electronic one. Aim to make good power at around 10-12psi, this is enough on the factory turbo to get you a low 13.

* Consider the front mount upgrade carefully. Pick the correct size based on your final application. If you are going to be happy with the factory turbo then reconsider getting one, it won't stop you doing low 13 quarter mile passes. As a note consider how many people can't go that quick with a front mount on the stock turbo (there are reasons why).

* exhaust improvements are a great idea. go for it.

Other things to consider...

Pineapples $100 and gets you more traction.

Adjustable exhaust cam gear. Retarding the timing on the exhaust cam nets you some earlier boost and about 10hp right through the power band. $200 DIY.

Lightweight flywheel (assuming you don't have an auto) .Along with an upgraded clutch this is worth putting in to experience increased acceleration (I gained almost half a second drop over the 1/4).

The forced induction section has plenty of good info so you don't have to reinvent the wheel.

Learn a little and you won't become a 'bolt on boy'. Instead you go faster for less effort. It's fairly easy and cheap to get low 13's out of an R33 gtst, you just need a little 'good' information. There is plenty around.

Link to comment
https://www.sau.com.au/forums/topic/62496-advise-on-mods/#findComment-1182063
Share on other sites

Hi Rev210,

Yes the faster factor is what I intend on achieving.

With the front mount option, I do intend on upgrading the turbo down the track so I think getting one installed would be the way to go.

I think it's a great idea what you said about the SAFC II and saving up for a PFC later. I think this guy quoted me $660 + $110 to tune.

Although, considering I want to put a bigger turbo in later, do you think I should get the electronic boost controller now?

I will head off to the forced induction section and have a read I think!

Thanks very much for the info mate!

Link to comment
https://www.sau.com.au/forums/topic/62496-advise-on-mods/#findComment-1182687
Share on other sites

you can import a brand new SAFCII from greenline or nengun i think it was for $450 landed in under 2 weeks.

My friend got his Power FC from Greenline for $1100 landed in less than 2 weeks so you won't need to search around for 2nd hand.

also look into getting more traction as the pineapples was mentioned. the more of that power hits these ugly bumpy streets we got here the better but you need to be able to control that power.

Link to comment
https://www.sau.com.au/forums/topic/62496-advise-on-mods/#findComment-1185412
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, there's a very minor drift left that happens a few seconds after letting go of the steering wheel, but not enough to bother me. Enjoying the car still!
    • Got you mate. Check your email!
    • I see you've never had to push start your own car... You could save some weight right now...
    • Sounds good.  I don't 100% understand what your getting at here. When you say, "I keep seeing YouTube videos where people have new paint and primer land on the old clearcoat that isn't even dulled down" do you mean this - there is a panel with factory paint, without any prep work, they paint the entire panel with primer, then colour then clear?  If that's what you mean, sure it will "stick" for a year, 2 years, maybe 3 years? Who knows. But at some stage it will flake off and when it does it's going to come off in huge chunks and look horrific.  Of course read your technical data sheet for your paint, but generally speaking, you can apply primer to a scuffed/prepped clear coat. Generally speaking, I wouldn't do this. I would scuff/prep the clear and then lay colour then clear. Adding the primer to these steps just adds cost and time. It will stick to the clear coat provided it has been appropriately scuffed/prepped first.  When you say, "but the new paint is landing on the old clearcoat" I am imagining someone not masking up the car and just letting overspray go wherever it wants. Surely this isn't what you mean?  So I'll assume the following scenario - there is a small scratch. The person manages to somehow fill the scratch and now has a perfectly flat surface. They then spray colour and clear over this small masked off section of the car. Is this what you mean? If this is the case, yes the new paint will eventually flake off in X number of years time.  The easy solution is to scuff/prep all of the paint that hasn't been masked off in the repair area then lay the paint.  So you want to prep the surface, lay primer, then lay filler, then lay primer, then colour, then clear?  Life seems so much simpler if you prep, fill, primer, colour then clear.  There are very few reasons to go to bare metal. Chasing rust is a good example of why you'd go to bare metal.  A simple dent, there is no way in hell I'm going to bare metal for that repair. I've got enough on my plate without creating extra work for myself lol. 
×
×
  • Create New...