Jump to content
SAU Community

R34GTR Skyline --HELP

zaxxon1
 Share

Recommended Posts

ferni Grand Master

ferni

Posted
Posted

Not sure what kind of knowledge you have with cars/tuning, but if you don't know much about these cars it may be worth getting someone else who does know them to tune it, but if you are from where your location says then, good luck :D

zaxxon1 Newbie

zaxxon1

Posted
  • Author
Posted
Not sure what kind of knowledge you have with cars/tuning, but if you don't know much about these cars it may be worth getting someone else who does know them to tune it, but if you are from where your location says then, good luck :rofl:

Yes, I am from trinidad and I am not too familar with this car and engine, I've tuned a couple WRXs and I work more on the Dragster's here. I do the electrical, computer and nitrous systems on the Rails. http://www.partytimeracing.20megsfree.com and http://www.mintcars.20megsfree.com.

I need information like the stock timing, if the car has a MAP sensor, the max boost on the stock engine etc. I already did some tuning on the car but I think I have not been able to get the full potential of the engine as yet.

ylwgtr2 Grand Master

ylwgtr2

Posted
Posted

the car has 2 airflow meters from factory,it has a map sensor but its for the gauge only and has no effect on the ecu.....the factory base timing is 15-20 degree's with the bac valve and tps disconnected....as for the link ecu,throw the thing up in the air and run as far away from it as possible before gravity brings it back to earth

zaxxon1 Newbie

zaxxon1

Posted
  • Author
Posted
the car has 2 airflow meters from factory,it has a map sensor but its for the gauge only and has no effect on the ecu.....the factory base timing is 15-20 degree's with the bac valve and tps disconnected....as for the link ecu,throw the thing up in the air and run as far away from it as possible before gravity brings it back to earth

There are no mods on the car as yet. The owner was told that the link would be able to faciliate upgrades later-on when he did any modifications. I'm stuck with it right now. I will have to do the best I can with it. It is twin turbo (stock), only 14 psi each (I think). What is the "bac valve"?. Where can I download a manual for this car (in english)?. I may be able to split the MAP sensor and send a signal to the link since it uses TPS and MAP for control. Do you think its better to run the car on TPS control alone?.

zaxxon1 Newbie

zaxxon1

Posted
  • Author
Posted
...why do you want to fit that useless peice of crap to the car?....

The owner of the car already had it installed in the car. He was duped into buying it. The original installer could not get the car working good, so they brought the car by me. I work on his Dragster so he thinks I can do a better job than the installer. I did manage to get his Idle down and the surging also the trottle response. I still have the boost problem where I need to retard for the boost and map fuel for higher speeds. The car is running rich at the moment but I had to leave it like that because the installer had the link set up for max boost and not incremental. I will have to find out what the installer did and get back to you. I know for a fact that the car is not firing sequential since they set it up for group injector firing, this I also have to fix. Do you have an e-mail address I can write to.

ferni Grand Master

ferni

Posted
Posted

ylwgtr2 knows his stuff so whatever he tells you i'd believe :D

If its a stock RB26, stock turbos, 14psi is on the safe side... if you want a push a little more a lot of people run 1 - 1.1bar on stock turbos... power with stock turbos and stock fuel system will probably net you around 250-280rwkw

zaxxon1 Newbie

zaxxon1

Posted
  • Author
Posted
throw it out and tell him to put the stocker back in?

or maybe just buy a power FC mate

mark

I contacted one of the tuners at LINK and he told me that they have got 295+HP from the stock R34GTR (at the wheels, without any mods) and with additional mods it can only go up. Then again, I am from Trinidad in the West Indies so I have to take what they say.

as I progress with the tune I will let you guys know. One thing, you can really get addicted to driving the R34GTR.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • EndZee
      R33 Gts/-t Abs Module Wiring Schematic (not Gt-r)

      By EndZee · Posted

      Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • GTSBoy
      Boost cut after swap(RB25DET NEO) R34

      By GTSBoy · Posted

      Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • dyl33
      VOLK RACING GTC CENTRE CAPS

      By dyl33 · Posted

      Centre caps $250
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Duncan
      Boost cut after swap(RB25DET NEO) R34

      By Duncan · Posted

      Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
×
×
  • Create New...