Jump to content
SAU Community

Recommended Posts

Ok,

So, if you really want your car to shoot a flame out (like a few feet) here is one way I've been told. I've also been told not to use it on the street, which I'll explain in a sec. I wouldn't do it myself.

As you are flooring the car getting ready for a shift, you set up your management to continue fueling as you push the clutch in (and back off for that second) as you go through the gears. It also retards the ignition which keeps the turbo on boost, and shooting raw feul out the back (which will catch fire if the exhaust is hot enough). Runs great, and heaps of fire (think v8 supercars). Cat, no cat, its doesn't matter, as long as you have a resonable sized pipe.

The downside is if you are driving down a hill, backed off, the car will still be feuling - which means the turbo will get HOT. Apparently even coasting down a hill for 30 secs or so can make a turbo glow red and fail.

Another system is to shoot a flamable gas (nos?) out the exhaust from near the diff, using a spark plug to ignite (ah lah Fast and Furious).

not that i'd bother...

That description doesn't just make a pop, its a rather big bang.

I don't think its harmful for a little pop every now and then, most skylines I know seem to have always done it....

You do not need to pump other gas into the pipe to create a flame, I've seen kits that work on a coil pack and a spark plug. They simply spark in the exhaust tip and bang, you have flame. Don't forget boys and girls, those gassesfumes are flamable!

http://www.flamethrowers.com.au

Rice anyone? Ooooh yar, 2F2F....

cars with a cat wont... some cars cats might be badly degraded (if its been on there for a few years etc) so you might get a flame.

Mine flames on the odd occasion... i think. Whether it makes it out the rear end or not i dunno. No-one's ever seen it.

You can tell the difference between a pop and a flame.

The sound is a tad different between the usual pop, and when the fuel catches.

not ture, i have a cat and i get flames (view the sauwa/silviawa cruise video) unless my abuses over the years has eaten it up

Pre-86 cars :(

In NSW (and ACT, which uses the NSW rules), an engine conversion on a car built from 1972 onwards has to meet the emmissions requirements of the year the engine was built in. Cars built prior to 1972 only have to meet the emmissions of when the car was built.

So - if you were to take a 1985 car and put an RB engine in it, you would have to run an exhaust choke... sorry, "catalytic convertor". I think it was the CEO of Lukey mufflers who commented that the best flowing catalytic convertors flowed almost as well as the worst flowing mufflers...

In my case, I can run aftermarket injection, play with cams, turbo etc. etc., and as long as I meet the CO/HC limits for 1971, I don't have to worry about the EPA.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
×
×
  • Create New...