Jump to content
SAU Community

Recommended Posts

Hi everyone,

I have bought a complete RB25DET motor and I am putting the head onto a standard 3L bottom end. I beleive the 3L is fairly strong. Provided that it holds up will it be possible to get 350RWKW out of it with only these bolt ons?

GT40, PowerFC, Intake Plenum, FMIC, 3" exhaust, 550cc side fed injectors.

Around how much boost will I need to run? Also if I need to run more boost, what is the best method to prevent detentation? ie water injection?

I wasnt sure whether or not to put this on the other thread but its too long to go through, sorry if something simliar to this has been posted. :Oops:

Thanks Edward

Link to comment
https://www.sau.com.au/forums/topic/64194-350rwkw-out-of-rb30det/
Share on other sites

an aftermarket head gasket would be nice to drop comp ratios a bit more so you can run higher boost.

Uprated fuel system to cope with the demand, just injectors won't be enough, a pump upgrade would be good, or just go the whole hog and get the propper high power fuel setup, with surge tanks etc

Best method to prevent detonation - don't mix high boost with an already high compression ratio. Give it a good dyno tune too, to get the cam timing right and the Fuel:Air ratios

rubbish.

rb30 bottom end and rb25 head will give it 8.3:1 compression... that's not high..!!

as for 350rwkw... it would definitely be pushing the stock rods and pistons at that level.

You really should read the 91 pages that are there in that thread.

also, saying GT40 turbo doesn't really mean anything.. what is it's rating? AR's etc... these will tell you if it will flow enough to produce the power you want.

these have been covered in that thread.

i wasn't saying it would give a high compression ratio, i was saying a higher compression ratio is something you want to avoid when running higher boost

Plus if you do change the gaskets then there's one less thing you will need to worry about later on

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
    • Little update  I have shimmed the solenoid on the rack today following Keep it Reets video on YouTube. However my steering is still tight. I have this showing on Nisscan, my steering angle sensor was the closest to 0 degrees (I could get it to 0 degrees by small little tweaks, but the angle was way off centre? I can't figure this out for the life of me. I get no faults through Nisscan. 
    • The BES920 is like the Toyota Camrys of coffee machines. E61 group head is cool, however the time requirements for home use makes it less desirable. The Toyota Camry coffee machine runs twin boilers and also PID temp control, some say it produces coffees as good as an E61 group head machine.
    • And yes with a full tank it will hit limiter free revving or driving 6B6CDF6E-4094-426D-A9CB-6C553475FE36.mp4
    • One way of putting the fuel surge idea to rest, is that even when in neutral/clutch in or free revving it still has the same issue, it can’t even get to limiter (7800) so to me that says it can’t be g force, I’m not trying to argue I just want to find the f&$king issue 😡
×
×
  • Create New...