Jump to content
SAU Community

Recommended Posts

I had a similar problem that went away when it warmed up.

The problem was a leak in the inlet manifold gasket. When it warmed up, and everything expanded the leak sealed up and it ran fine.

Wasnt untill the gasket blew out completely that I found the problem.

Link to comment
https://www.sau.com.au/forums/topic/64905-steroided-rex/#findComment-1216564
Share on other sites

haha sterioded rexxy means it aient kool for a skyline to sound like that!!!! is missing and sounding like a rexxy

no it only just happened now

only for a few mins wen its cold but its enough to do my head in!!!

QUOTE=600hp]I'm not sure what you mean by it goes like a rexy, does this mean it sounds crap or it gets off the line fast?

thanks.

also has this always happened since you have the car.

Link to comment
https://www.sau.com.au/forums/topic/64905-steroided-rex/#findComment-1221765
Share on other sites

Mine does that every now and then too.

Runs on one cylinder down.

Does sound a lot like a rex.

Mine goes away after a couple of revs, or just by itself after 10 seconds or so.

Happens very occasionally to me, and at very randow times, hot/cold whenever.

Link to comment
https://www.sau.com.au/forums/topic/64905-steroided-rex/#findComment-1227245
Share on other sites

Mine was doing the same thing when cold because the ecu thought the car hadn't warmed up yet so was pulling heaps of timing out... it sucked... would come good the exact same place on the way to and from work... weird

so wat can do 2 fix this prob???

if i dothe ecu codes test will it bring up an error code???

thanks 4 da help much appreciated

Link to comment
https://www.sau.com.au/forums/topic/64905-steroided-rex/#findComment-1227731
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • UPDATE: Yes the GSP Axles are compatible. I installed it on my R34 today and they are working a treat! Turns out that the S13, S14, S15, and 200 SX all used the same axles as the HR34, and ER34 NA models. Which is 2 bolt x 3 pairs.  
    • Also build this EH ute with 370z motor and gearbox with a couple of turbos just for fun.  
    • Got the passenger door on plus the master cylinder and booster. Loaded up to take it home. At home, the colour changes a lot in the light.
    • Nothing cheap, but I have seen the AC Hydraulic DK13HLQ which is pretty close to what you're asking for. The problem is the hydraulic cylinder mandates that the back of the jack be a certain height and Skylines have fairly deep inset floor jack points. A more certain and cheap option is to get some nominal 2x10 inch lumber boards and have one board be 1.5 feet, the other board 3 feet. Glue it all together with lots of clamps to maintain pressure. Make two of these. The ramp suggested above is a good idea, it takes quite a bit of clutch slip to get over each of the boards. I only need the first ~1.5 inches for my low profile jack on a standard ride height car but a lowered car you want to go up to the full ~3-3.5 inches. Paint it or store indoors if you want it to last.
    • Ok. And Nistune? I read (here too) mainly on Stagea threads that it can by "turn off" with Nistune. But they say they still had the sensor plug in. Next week iam going to the Nistune(and other ECUs) tuner so i can finally make it work. I drove the car home and apart from the cut it drove great. No misfire no smoke no hesitation or rough start...so hoping it is this sensor that is missing  
×
×
  • Create New...